If the Status Light is flashing once every three seconds, the pilot light is lit and the gas control valve is working properly. Make sure the gas control valve is turned to “Hot” and wait for the water heater to heat back up. It may take several hours for the water to heat up.
Should water heater have status light?
1 flash every 3 seconds means the pilot is lit and the gas valve is working normally. A solid red status light means the water heater is shutting down.The status light will flash more than once every 3 seconds if an error is detected.
What does blue status light mean on water heater?
Unless it is explicitly disabled, and ETE or ITE are not installed, the blue LED flashes if any of the following are true: Battery Charge is below 10% Battery Life is less than 15%
How long does it take for a hot water heater to reset?
Speed of Recovery
A gas water heater will recover in half the time of an electric unit. A 40-gallon gas water heater can recover in about an hour. Recovery for a 40-gallon electric water heater takes about two hours.
Why is the status light on my water heater not working?
Try lighting the pilot following the lighting instructions on the water heater and visually confirm the pilot can be lit.If the status light does not start blinking after 90 seconds, release the gas control knob, turn the gas valve off, and wait 10 minutes before attempting to relight the pilot.
How do I know if the pilot light is out on my water heater?
It’s usually right on the panel. Turn and hold the knob to Pilot and push the ignitor. You should hear it click, and probably also a whooshing sound. Check in that gap, and you should see the light on.
How long does it take for water heater to heat up?
between 30 and 40 minutes
The average gas heater takes between 30 and 40 minutes to fully heat up the water in its tank. The average electric heater takes about twice as long as the average gas heater to fully heat up the water in its tank, so you can expect it to take between an hour and an hour and 20 minutes to heat up.
What does blue flashing light on boiler mean?
The blue light on an RI will flash when it detects no gas supply, or low pressure. This could be a range of things such as a faulty gas valve. As this issue relates to gas, contact a heating engineer straight away. Another common cause of a blue light flashing is a blockage in the flue.
Why is my hot water heater not getting hot?
If an electric water heater is not producing hot water, it could be a simple problem like a blown fuse or tripped circuit breaker. Additionally, some electric water heaters have a circuit-style safety switch located near or on the thermostat.
The high resistance caused by a loose wire produces a substantial amount of heat that can eventually cause fires. If there is a loose electrical connection within your water heater’s system, your reset button’s thermometer can trip (regardless of the water’s temperature) if it picks up the heat from that loose wire.
How long should the hot water last?
In general, if you have a 40 gallon water heater your hot water should last about 45 minutes to an hour.
Why did my water heater pilot light go out?
Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple.Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. A bent or dirty thermocouple.
Why does the pilot light on a water heater?
The most common reason that your pilot light on your water heater keeps going out is a damaged, bent or dirty thermocouple.
How much does it cost to replace a water heater thermocouple?
Thermocouple $20 to $150
The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.
How do I know if my gas hot water heater is on?
Start by looking for an access panel on the side of the water heater. If you remove it and see a blue flame, that’s a pilot light, which only gas models have. Connected pipes are also indicators of gas, while an electric water heater will simply have a cord going into the top or side of the unit.
What would cause no hot water?
If there is no hot water or the supply is not adequate or is too hot, check the upper thermostat. If the thermostat is busted, it should be replaced. Lack of regular maintenance can cause issues even though the thermostat is working because of sediment buildup. To fix this, flush your water heater.
How do you fix a pilot light on a hot water heater?
How to Fix the Pilot Light of Your Water Heater
- The first step is to open the cover or door of the pilot light access.
- With the help of a flashlight or headlamp, identify the burner inside.
- Now, turn and press the knob to ‘Pilot’, and hold it for some seconds.
How do I know if my water heater is working?
7 Tell-tale signs of a Water Heater not working
- You don’t have enough hot water.
- You have varying water temperature issues.
- You have a leaking water heater.
- You notice reduced water flow.
- You’re hearing some concerning sounds.
- You have smelly or discolored water.
- Your water heater is on the older end of the spectrum.
How long does it take a 40-gallon water heater to heat?
If you have a 40-gallon, 5500-watt electric water heater and set it to 120 degrees, it will take about an hour to an hour and 20 minutes to heat up.
Is it cheaper to leave water heater on all the time?
It is a myth that leaving your hot water on all of the time will save you money. Unless you need a constant supply of warm water, your boiler will be constantly heating when there is no real need. It is cheaper and more energy-efficient to switch your boiler on, only when you need the hot water.
How do I reset my boiler?
Follow these simple instructions to reset your boiler:
- Refer to your boiler manual.
- Push the reset button for 10 seconds.
- Wait 2 – 3 minutes, the boiler should fire up.
- Repeat twice if the first attempt fails.
- If the boiler still fails to fire up on the third attempt, double check the gas supply.
Contents