Why Is My Wifi Camera Not Working?

Check if the power supply of the wireless IP camera is working properly. Make sure the power adapter is plugged into a working socket. If you get a battery powered wireless IP camera, check if the battery is still at work. Change or charge up the battery.

Why won’t my WiFi camera connect?

Hold your phone in the location of your camera and check the number of dashed Wi-Fi coverage on your phone. If the connection is poor, if possible, reduce the distance between the camera and your Wi-Fi router. Consider a wired installation or consult your internet provider for solutions.

How do I fix my WiFi camera?

The Top Ten Tips of Troubleshooting

1. Reboot the camera.
2. Ping & discover the camera.
3. Check ARP tables.
4. Check for IP conflicts.
5. Verify camera power & connection.
6. Check the cabling.
7. Know the password.
8. Upgrade Firmware.

How do I reset my camera for WiFi?

Switch off the network camera by disconnecting the power adapter. Press and hold the reset button with a straightened paperclip while reconnecting the power. Keep the reset button pressed until the status indicator blinks. Release the reset button.

How do I get my camera back online?

Disconnect the Camera from the Power Source and Power Cycle it. The very first thing to try in order to get your camera back online is to disconnect it from the power source. Unplug the camera and let it sit for a few minutes and after a few minutes have passed, plug the camera back in.

How do I connect my wireless camera to my wireless router?

How to use Wireless Security Cameras with a WiFi Router

1. Step 1: Determine the WiFi strength of your wireless network.
2. Step 2: Power and Configure the Wireless Security Camera for your Network.
3. Step 3: Access the IP Camera’s Web Interface.
4. Step 4: Configuring the WiFi Address.
5. Step 5: Connect to Your Wireless Router.

Why is my IP camera not working?

Reboot the device. Rebooting your security camera will release its cache to flush, re-calibrate the settings, and revise connections. Directly unplug the security camera from its power supply then wait for a few seconds before plugging it again. This will reboot it.

Why is my IP camera offline?

Occasionally, your camera may go offline due to network connectivity.Even if your camera is not too far from your router, there may be different materials (walls, floors, metal, concrete, plaster) that can block the WiFi signal. Minimize the number of physical obstructions between the camera and router.

Why is my security camera not recording?

If your CCTV camera is working fine but the DVR is not recording anything, common culprits include misconfiguration, lack of storage space, and failing DVR components. Don’t despair: modern DVR boxes are pretty friendly and easy to troubleshoot. Check that recording is enabled. It may sound obvious, but it happens.

How do I change from 2.4 GHz to 5ghz?

To connect your Android device to a 2.4 GHz network:

1. Unlock your device and tap the Settings app.
2. Tap Network & Internet > Wi-Fi.
3. Enable WiFi by tapping Use WiFi at the top.
4. Select a 2.4 GHz WiFi network.
5. If prompted, enter the password for the network.

How do I reset my IP camera to factory settings?

How to reset IP Camera to factory defaults

1. Keep the device powered on for at least 30 seconds to complete its normal startup.
2. Find something like a pin to press the Reset button on the camera and hold it for 15 seconds to restore the settings to factory defaults.

How do I reset my IP address for my IP camera?

How do I change the LAN IP address of my camera?

1. Step 1: Open a web browser and enter the IP address of the camera in the address bar (default is 192.168.
2. Step 2: The default username is admin and the password field should be left blank.
3. Step 3: Click on Setup on the top menu bar.

How do I restart my camera?

Disconnect your camera from power by unplugging the power adapter from the electrical outlet. Wait 10 seconds. Plug the power adapter back into an outlet. Your camera will restart.

Why does my WiFi camera keep disconnecting?

If the camera keeps disconnecting, maybe the WiFi signal is not so good.2: Check the camera and the WiFi Hotspot distance is not far and whether it is blocked by several walls. 3: If there are many 2.4G wifi device, please change the Router’s WiFi channel.

How do I get my IP camera to work?

Plug an Ethernet cable (a.k.a. Cat 5 cable) into the Ethernet socket of the network camera, then plug the other end to the router (a.k.a. gateway or access point). If this network camera does not have Wi-Fi, this may be the only step needed for the network configuration. Find the IP address of the network camera.

Can wireless camera work without internet?

Wireless security cameras don’t necessarily require the internet. Rather, there are a number of security cameras that can record their footage locally onto micro-SD cards or hard drives so it can be viewed later.

How do I fix my security camera?

How do you troubleshoot a security camera?

1. Know your login details.
2. Check the power source (most cameras are PoE)
3. Check to see if cameras work from inside or outside the network.
4. Check the cabling.
5. Reboot the system.
6. Check for IP conflict.
7. Check ARP tables.
8. Update software & firmware.

How do I know if my WiFi is 2.4 or 5?

1. From Notification Panel press and hold the WiFi icon until you enter WiFi settings screen.
2. Select the network properties (tap the gear icon or menu icon).
3. Depending on the Android version check: Read the “Frequency” setting – shows as 2.4 or 5GHz.

Is my WiFi 2.4 or 5 iPhone?

IPhone Users
To verify your mobile device is set to a 2.4GHz Wi-Fi network, navigate to the Settings menu and click on Wi-Fi. In this menu you will see all detectable networks in your area. Locate the SSID for your network, the SSID should be denoted by either a 2G (2.4) or 5G (5) end notation.

What GHz is iPhone hotspot?

Historically, all iPhones have created Personal Hotspot connections over 2.4GHz networks, which are supported by the widest range of devices out there. All new iPhone 12 models support 5GHz transfer by default when Personal Hotspot is enabled.

How do I factory reset my HIKVision IP camera?

To reset your camera back to factory defaults:

1. Disconnect the power supply.
2. Press and hold the reset button.
3. Keep holding the reset button and restore the power supply.
4. Continue to hold the reset button for a further 10 seconds.
5. Release the button and allow the camera to complete a restart/reboot.