Why Is My Smart Light Not Connecting To Wi-Fi?

1 – Check that the lamp or bulb is within Wi-Fi range. Go next to the bulb or lamp with your mobile, and check that you are well connected to Wi-Fi. If the bulb is too far away, it cannot connect. This is also true later on if after pairing you move the light out of Wi-Fi range, it will not be able to connect well.

Why is my smart light not connecting to Wi-Fi?

Make sure the Wi-Fi network is a 2.4 GHz network. The Smart Wi-Fi Light will not connect to a 5 GHz network.The Wi-Fi connection may not have good coverage during set up. You may need to improve your Wi-Fi network coverage by upgrading your router or adding a range extender.

How do I make Wi-Fi 2.4 GHz?

Using the Admin Tool

1. Connect to your WiFi network.
2. Go to Gateway > Connection > Wi-Fi. To change your Channel Selection, select Edit next to the WiFi channel (2.4 or 5 GHz) that you’d like to change, click the radio button for the channel selection field, then select your desired channel number.
3. Select Save Settings.

How do I change from 2.4 GHz to 5GHz?

To connect your Android device to a 2.4 GHz network:

1. Unlock your device and tap the Settings app.
2. Tap Network & Internet > Wi-Fi.
3. Enable WiFi by tapping Use WiFi at the top.
4. Select a 2.4 GHz WiFi network.
5. If prompted, enter the password for the network.

How do I connect my Alexa WiFi lights?

How to connect Alexa to smart lights

1. Open the Alexa app, then turn on the light you want to connect.
2. Navigate to the Devices tab, then tap All Devices. Quick tip: If you see a button that says Lights, tap that to connect.
3. Scroll down the list to find the light you want to connect. Tap the name of the light.

How do I connect Alexa smart lights?

Connect a Smart Light Bulb to Alexa

1. Open the Amazon Alexa app on your mobile device.
2. Select the Devices tab.
3. Choose All Devices.
4. Scroll down to find the smart light that you want to connect.
5. Tap the smart light’s name to complete the setup.

Why are my lights offline?

A power outage, router, or internet service provider disruption. If your smart device loses power by a light switch being toggled off or a fixture being turned off.If there are changes to your network, a new network name, new network password, or a new router or range extender could all disconnect your bulb.

Why does it say my lights are offline?

If your Smart Strip Light is disconnected you will need to connect it again using the Feit Electric app. You will need to confirm that it is in AP pairing mode or press and hold the controller button until the lights are blinking slowly.

Why are my smart devices offline?

Smart Life devices go offline due to overloads in your router when your router renews the LAN/WAN IP address, or if there are errors stored in its cache. Solutions to this problem include clearing the cache or using a dedicated 2.4g WiFi router for Smart Life devices.

Can’t connect to smart bulb?

Pairing Troubleshooting

1. 1 – Check that the lamp or bulb is within Wi-Fi range. Go next to the bulb or lamp with your mobile, and check that you are well connected to Wi-Fi.
2. 2 – Check that your phone is connected to the 2.4 GHz Wi-Fi on your home router.
3. 3 – Start pairing in the WiZ app.

Why is my smart bulb not working?

If your smart light bulb isn’t working, or Alexa can’t discover it, reset your device. To reset your smart light bulb: Go to the manufacturer’s companion app or website to follow instructions specific to your device. Reconnect your smart home device to Alexa in the Alexa app.

How do you check if my WiFi is 2.4 or 5?

1. From Notification Panel press and hold the WiFi icon until you enter WiFi settings screen.
2. Select the network properties (tap the gear icon or menu icon).
3. Depending on the Android version check: Read the “Frequency” setting – shows as 2.4 or 5GHz.

How do I know if my WiFi is 2.4 or 5?

If you have an Android phone, you can definitively confirm whether the network is 2.4G or 5G.

1. Connect to the network.
2. Go to Settings > Network & internet > WiFi > Select the network properties (tap the gear icon or menu icon).
3. Read the frequency setting.

What is the difference between WiFi network of 2.4GHz and 5GHz?

2.4 GHz vs. 5 GHz: Which frequency should you choose? A 2.4 GHz connection travels farther at lower speeds, while 5 GHz frequencies provide faster speeds at shorter range. Your choice of 2.4 GHz or 5 GHz will depend on where and how you use your WiFi connection most.

What devices should be on 2.4GHz and 5GHz?

Ideally, the 2.4GHz band should be used to connect devices for low bandwidth activities like browsing the Internet. On the other hand, 5GHz is the best option for high-bandwidth devices or activities like gaming and streaming HDTV.

How do I change my Wi-Fi frequency?

The frequency band is changed directly on the router:

1. Enter the IP address 192.168. 0.1 in your Internet browser.
2. Leave the user field empty and use admin as the password.
3. Select Wireless from the menu.
4. In the 802.11 band selection field, you can select 2.4 GHz or 5 GHz.
5. Click on Apply to save the Settings.

How do you check if your Wi-Fi is 2.4 or 5 IPhone?

IPhone Users
To verify your mobile device is set to a 2.4GHz Wi-Fi network, navigate to the Settings menu and click on Wi-Fi. In this menu you will see all detectable networks in your area. Locate the SSID for your network, the SSID should be denoted by either a 2G (2.4) or 5G (5) end notation.

Why can’t I connect to my LED lights?

Bad Pin Connection – If your LED strip light fails to turn on at all, then check your pin connections. Most likely, the pin is not inserted correctly. In rare cases, the pin is faulty. These tiny connectors are rather delicate items so you have to be very careful when inserting them.

Why won’t my LED lights connect to Bluetooth?

Try to reset the light strip. Reset: Press the middle button on the control box for four times while holding the power button.Please try to unplug the light strip for 10 mins, then re-plug it.

How do I reset my LED strip WiFi?

press and hold the power button of wifi led controller for 5-6 seconds , then you can reset the light strip controller again.

How do you reset a smart light bulb?

Turn the bulb off for 2 seconds, then on for 2 seconds. Repeat three more times. After the fourth cycle, the bulb will flash, indicating that the reset was successful.