If the Status Light is not flashing, try lighting the pilot using the instructions on the water heater’s label. Make sure the gas supply valve is turned ON. When lighting the pilot, make sure the knob on the gas control valve is fully pushed in.
How do I know my water heater is lit?
It’s usually right on the panel. Turn and hold the knob to Pilot and push the ignitor. You should hear it click, and probably also a whooshing sound. Check in that gap, and you should see the light on.
Is the status light on water heater supposed to blink?
The red status light will blink once every 3 seconds when the water heater is operating normally. Once the red status light is blinking, release the knob. Set the temperature to the desired setting. We recommend a maximum temperature setting of HOT (120°F) to reduce the risk of scalding.
Why is the status light on my water heater not working?
Try lighting the pilot following the lighting instructions on the water heater and visually confirm the pilot can be lit.If the status light does not start blinking after 90 seconds, release the gas control knob, turn the gas valve off, and wait 10 minutes before attempting to relight the pilot.
What causes water heater pilot to go out?
Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple.Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it’s burning properly. A bent or dirty thermocouple.
Should the water heater be on pilot or on?
On gas water heaters, the pilot light makes sure that there’s always flame available when the burner needs to kick in and heat water. If you run out of gas, install a new water heater or have to shut it down for some reason, lighting the pilot is the first step to turn on a water heater.
What does a green flashing light mean on a hot water heater?
If your water heater flashes green 5 times every 3 seconds, you might have a problem with a sensor. Call a technician to replace a gas control valve. Gas control valve failure. If the LED light blinks 7 times every 3 seconds, you have a problem with a gas valve.
What does a blue blinking light mean on a water heater?
A flashing blue light on a water heater could mean any of the following depending on your model: A call for heat. A draft pressure switch error. Blocked diameter vacuum tubing.
What does a flashing green light on a water heater mean?
1 FLASH (GREEN DIAGNOSTIC LIGHT)
Indicates power has been applied to the heater prior to filling with water. Open the nearest hot water faucet, and fill the water heater until a steady stream of water .
How do I know if my pilot light is out on my water heater?
When a water heater pilot light goes out, it usually means that a natural change in gas pressure extinguished the flame. The main sign that a pilot light is out is one that everyone dreads: The water won’t get hot.
How long do hot water heaters last?
Typically a residential hot water heater lasts between 6 and 13 years.
The high resistance caused by a loose wire produces a substantial amount of heat that can eventually cause fires. If there is a loose electrical connection within your water heater’s system, your reset button’s thermometer can trip (regardless of the water’s temperature) if it picks up the heat from that loose wire.
How long does it take for a water heater to heat up after resetting?
The average gas heater takes between 30 and 40 minutes to fully heat up the water in its tank. The average electric heater takes about twice as long as the average gas heater to fully heat up the water in its tank, so you can expect it to take between an hour and an hour and 20 minutes to heat up.
Some heaters may not click when you press on the reset button. If you don’t hear the click even after pressing on the button for about five seconds, reassemble the heater anyway. It will probably still restore hot water.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How much does it cost to replace pilot light on water heater?
Pilot light replacement or lighting cost
Water heater pilot light replacement costs $50 to $200. The pilot light produces a flame to ignite the gas burner. Plumbers charge $45 to $150 per hour to reignite the pilot light, and the task typically takes 1 hour or less.
How do I know if my water heater is working?
7 Tell-tale signs of a Water Heater not working
- You don’t have enough hot water.
- You have varying water temperature issues.
- You have a leaking water heater.
- You notice reduced water flow.
- You’re hearing some concerning sounds.
- You have smelly or discolored water.
- Your water heater is on the older end of the spectrum.
What does it mean to have no hot water?
If there is no hot water, it probably means that the tank is leaking. An empty tank is a serious problem and is not at all energy efficient. Inspect the connections between the appliance and its valves as well as the pipes. If those are secure, check the tank’s compartment.
Can a water heater explode?
If the heating element and/or thermostat were to malfunction, the temperature of the water inside the tank could increase to the point where it is producing steam. If the situation progresses, and there is no outlet for the steam, the increased pressure could cause the hot water tank to explode.
What could be wrong with my hot water heater?
When there’s no hot water, the problem can stem from lack of power, a faulty electric thermostat or a faulty upper electric heating element.When the water’s not hot enough, the problem can be an undersized water heater, crossed hot and cold connections, or a faulty heating element or thermostat.
Contents