Changing the batteries. One of the most common reasons for wireless room thermostats not working properly is the batteries running out. Thankfully it’s a simple fix, and most thermostats take standard AA batteries. But always check the manual for full instructions on how to replace the batteries.
How do I reset my hive thermostat?
To reset the thermostat, hold the thermostat in your hand with the back facing you. Hold down the ‘+’ and ‘-‘ buttons on the front of the thermostat at the same time. Keep a hold of those buttons while putting the battery back in and keep holding them in until the word ‘FIND’ appears on the screen.
Why is my hive thermostat not connecting?
Remove the batteries and put them straight back in again. This will turn the thermostat off and on which should help establish a connection to the receiver. Place the thermostat back on the wall, the thermostat should then display a ‘Reconnecting’ message.
Why has my hive stopped working?
Check that your products are connected to the mains power socket and the socket is switched on OR that the batteries haven’t run out. For help on replacing the batteries see our user guides. 6. For Hive Active Plugs check that the electrical device you have plugged into your Hive Active Plug is switched on.
How do I reconnect my hive thermostat?
How to reconnect a Hive
- Press the tab on the base of the thermostat to remove it from the wall.
- Remove the batteries and put them straight back in again.
- Place the thermostat back on the wall, the thermostat should then display a ‘Reconnecting’ message.
Why is my thermostat not working?
Try replacing the batteries, then check for a blown fuse or tripped breaker in the electrical panel. If the thermostat is still unresponsive, make sure the breaker is shut off and remove the cover.If the wiring looks corroded, consider replacing the thermostat.
What does resetting a thermostat do?
From time to time, it may be necessary to reset your home’s thermostat. Resetting your thermostat means you are resetting it to its factory setting, which can help resolve issues with programming, your HVAC system or thermostat connection issues.
How long does it take for hive thermostat to reconnect?
This usually takes 5-10 minutes. Once the AMBER light is flashing, the hub is set up and you can move onto installing the receiver. If no lights are displayed immediately after the hub has been turned on, check all cables are connected and the power socket works.
What does a red light on my Hive mean?
What to do if your Hive Receiver has a red status light. If your receiver has a red status light this means it has lost connection to your thermostat. This could be due to poor signal between your devices or flat batteries in your thermostat.You should turn your lights back on once the thermostat has reconnected.
Why is my Hive receiver flashing green?
Flashing Fast Green = Hub is trying to connect to the internet. Flashing Slow Green = Hub is trying to connect to the Hive servers or is in upgrade mode. Wait for 20 minutes and refresh your Hive app.
How long do hive thermostats last?
Hive Active Heating 2 is a little simpler, with four AA batteries powering the thermostat. This makes placement easier; you can put the thermostat on any wall that you like. Hive quotes battery life at around two years. Both devices can be self-installed if you’re a competent DIYer.
How do I check the battery on my hive thermostat?
Find and press the small tab on the underside of your thermostat. Unhook the unit from the mount to take it off the wall. This will expose the battery housing at the back of the thermostat. Take out the old batteries and replace with fully charged ones Hive thermostats take four AA batteries.
Why has my hive gone offline?
If your Hive Light is showing as offline in your Hive app or website dashboard it could be because it’s been switched off manually from the existing light switch on the wall or lamp.If your wall or lamp light switch is switched to on and you’re still unable to control Hive Light remotely, try restarting your Hive Hub.
How do you know if your thermostat is broken?
HVAC system won’t turn on: The most obvious sign of a bad thermostat is that the HVAC system in your building won’t turn on or respond to the thermostat. You should be able to turn on your heating or cooling system from the thermostat, or change operation back and forth from heating to cooling.
What causes no power to thermostat?
The power is out or a circuit breaker has tripped
If the blank thermostat occurs during the day, it’s possible that you have lost electrical power to your house and haven’t noticed it yet. The power loss could also be the result of a tripped circuit breaker that powers the air conditioner or heater.
Does my thermostat need to be replaced?
7 Signs You Need to Replace Your Thermostat
- Your HVAC Keeps Turning On or Off.
- Faulty Thermostat Readings.
- Suspiciously High Energy Bills.
- Constant Temperature Shifts.
- Thermostat Is Too Old.
- Thermostat Fails to Respond to Changed Settings.
- Your HVAC System Short Cycles.
Arrow Buttons Normally, a thermostat has two arrow buttons for resetting the temperature higher or lower. If you adjust these, the new setting is temporary, only lasting until you have reached the end of the previously set program.
When should I reset my thermostat?
Anytime you suspect an issue with your HVAC system, resetting the thermostat should be your first course of action. Like personal electronics such as tablets and phones, sometimes these devices need a reset.
An AC’s reset button is typically red and visible, so it should be easy to spot. If you don’t see a reset button on the outside, it could be located inside the unit behind the service panel. Before poking around inside the machinery, be sure to cut power to the system by flipping off your circuit breaker.
How do I reset my Hive hub UK?
The Hive Hub can be reset by pulling the power cable out and putting it back in again. It will take about 5 minutes to fully reboot and pair to your devices. After the 5 minutes, refresh the app or website.
What does orange light mean on Hive?
If your hub is showing red or amber flashing lights this means that the hub is trying to recover from a connection failure or a power cut. You may also see your heating showing as ‘offline’ in the Hive app dashboard.
Contents