You will need a shower rod and shower curtain hooks. If the shower curtain doesn’t have holes for hanging, it is defective & you should return it.You need to purchase rings that will connect the curtain to your shower curtain rod.
How do you make a hole in a shower curtain?
Cut a hole in the curtain with the long point of a seam-ripper tool. Work the blade around the fabric in a circle, using the holes you drew in pencil as guides. You can also use a sharp-bladed craft knife to make holes in the fabric.
Do shower curtain liners have holes?
Metal grommet holes: The liner provides 12 metal grommet holes to accommodate the shower curtain hooks, or other decorative hooks.
What are the holes in a shower curtain called?
Typical Grommet Uses
One of the most common applications of grommets is hole reinforcement in fabric, as in bootlace holes and shower curtain holes. The grommet is easy to install using a grommet-setting tool, essentially a rod with a curved tip, and a hammer.
How can I hang curtains without putting holes in the wall?
Here are five ways to hang curtains without damaging walls or window frames:
- Use 3M Command Hooks.
- Try Kwik-Hang Curtain Rod Brackets.
- Use Tension Rods.
- Get Creative With Coat Hooks.
- Try Magnetic Rods on Metal Doors.
Can you hang curtain rods without drilling holes?
Dowels and Sticky Hooks
A slim wooden dowel is a beautifully understated way to hang curtains.And the beauty of using a sticky hook instead of drilling holes in the wall is that if you decide the curtains look too low or too high, you can move the rod and hooks without any damage.
How many holes does a shower curtain have?
A standard shower curtain has twelve grommets and a standard pole carries twelve hooks.
How far apart are shower curtain holes?
The grommets on either end of the curtain should be spaced 1 from the edges of the curtain (hence the minus 2). Shower curtains typically hang from 12 hooks with 11 spaces in between those 12 hooks, so you will divide your width minus two amount by 11. For example, my curtain was 78 wide.
What is the difference between shower curtain and liner?
A shower liner will hang to the inside of your shower or tub and prevent any water from splashing out onto your bathroom floor. On the other hand, a shower curtain hangs to the outside of the tub and provides privacy but doesn’t stop water from getting out.
Do shower curtains go inside or outside of the tub?
Ideally, the curtain should be hanging inside the tub, keeping the water from getting out of your shower area. Hence, if you’re not using your bathroom, you can put it outside to hang. Indeed, shower curtains have a significant role in protecting the tiles outside your shower area.
How do I stop my shower curtain from blowing in?
Here’s how to stop your shower curtain from blowing in on you
- Buy a weighted curtain. Most department stores carry shower curtains that have weights on the bottom to prevent them from blowing around.
- Upgrade your curtain liner.
- Install a curved shower curtain rod.
- Grab a suction cup and binder clip.
- Try magnets.
How many eyelets should be in a shower curtain?
Standard shower curtains are 72 square with twelve grommets or buttonholes across the top to correspond to the hook placement in the accompanying vinyl liner. Measure your tub or shower to be sure this size works for you and adjust as needed to fit.
How many holes are in a 72 inch shower curtain?
12 holes
60×76 (10 holes) 60×80 (10 holes) 72×72 (12 holes)
What is a rod pocket?
Rod pocket means that the rod will go through the pocket on the back of the curtain and back tab means that there are also tabs in the back of the curtain if you wish to hang it like that.If you hang through the rod pocket, it may not be as easy to move the curtain as it would be if you hung through the back tabs.
How can I hang curtains without a curtain rod?
For stationary curtains, it’s easy to hang them without a rod using upholstery tacks.
5 Creative Ways to Hang Curtains Without Rods
- upholstery tacks.
- tension cables.
- hook-eye screws and drapery pins.
- staples and furring strips.
- cabinet knobs.
Can you hang curtains in drywall?
Hanging curtains on drywall is not as simple as it looks. Drywall will not hold a screw because it’s not solid. If you mount a curtain rod with a screw, over time you will end up with a sagging curtain and hole. Using drywall anchors is the only solution.
What can I use in place of a curtain rod?
copper pipes
Pipe Rods. This one is a pretty common alternative. Many people turn to copper pipes when they need a substitute curtain rod. Copper pipes have a unique look about them which is what draws many folks toward it, but you can use any style of or look of pipe.
Can you hang curtain rod with command strips?
They can be merely decorative, or they can serve to block out the light. Many landlords don’t allow renters to drill holes into walls, which is necessary for installing curtain rod hooks. Fortunately, it is still possible to install curtain rods with Command hooks.
Can you install curtains with a screwdriver?
A handheld screwdriver works well for the last few turns. Once you have your brackets attached to the wall, you’re ready to hang your curtain rod! It’s easiest to thread your curtains on the rod beforehand.
How many shower curtain rings does the typical shower curtain have?
A standard shower curtain requires twelve shower curtain rings. Shower curtains are built with a series of small holes on the top edge of the curtain where you insert the rings.
What is the standard shower curtain size?
x 72 inches
Across the board you’ll find three options when it comes to standard shower curtain sizes: 70 x 70 inches. 70 x 72 inches. 72 x 72 inches.
Contents