What should you avoid when using a jointer or planer? Do not cut stock that has loose knots, splits, defects or foreign objects (e.g., metal stone) in it. Do not leave the machine running unattended. Shut off the power and make sure that the cutting head has stopped revolving before leaving the area.
What should you not use a planer for?
Be cautious of loose knots, splits and other defects in wood. These defects can jam planer. Never run materials containing nails, screws or other metallic objects. Don’t remove debris unless planer has come to a complete stop and is locked out.
How should stock be fed into a planer?
12. When running short stock, always butt the ends of the boards against one another as they are fed into the planer. 13.
When operating the planer you should stand?
Never stand or walk directly behind the machine when it is in operation. 3. Do not overload the planer by trying to cut more than the capacity of the machine. The depth of cut will depend upon the width of the lumber, rate of feed and the kind of lumber.
Can I put small pieces of wood through a planer?
The planer will cut the outriggers as well, but they are scrap. More importantly, it will allow you to plane short pieces.
Can you run wood through a planer against the grain?
Always try to plane with the grain rather than against the grain. Planing against the grain can cause the wood to tear out. This is because when planed against the grain the blade lifts a chunk of the top wood fibers and separates it from the fibers below it.
When using the planer the workpiece must be at least?
Plane a warped board only after one surface has been trued on a jointer. Wear eye protection. Make sure that the board is at least 2 inches longer than the distance between the feed rolls. For a small planer, this usually means a board should be at least 14 inches long.
What is the main use of a planer?
A planer is used to shave wood from the surface of boards. Imagine scraping a knife across the top of a block of butter. That’s pretty much the action with a planer – though you might need a bit more muscle power! They’re used to make a rough surface flat and smooth, or to reduce its thickness.
Will a planer fix warped boards?
In order to flatten a warped, twisted, or cupped board, a common approach is to first use a jointer to create one perfectly flat face. Then you run the board through a thickness planer with the flat face downward, and the planer makes the top face parallel to the bottom.
How thin can a planer cut wood?
1/4″
Most planers aren’t very happy running stock that’s less than 1/4″ in thickness. Once the wood gets that thin, it becomes very light and flexible and there’s a good chance it’ll be sucked up into the planer blades which will quickly turn your fancy planer into a wood chipper.
How thin will a Dewalt planer go?
1/8"
The minimum planing thickness of theplaners is 1/8″.
Can you run bamboo through a planer?
In short, carbide works well on bamboo but steel planer blades don’t, and sanding is the best way to get surfaces with no tearout.
Does a planer cut both sides?
With one flat face, you can now put the flat face down on your planer bed and pass it through to flatten the opposite face. Since you already have one flat face to index off of, your planer will cut the opposing face parallel to the flat face.
Which way does a planer spin?
If you’re looking at the exterior or “bark” side of the board, these arrows point uphill. On the interior or “heart” side, they point downhill. Knowing this – and which way your cutterhead spins – you can determine how to feed the board into the planer.
What is direction of grain?
As the fibers travel through the machine on a vibrating mesh, they tend to line up in the same forward direction, parallel to the direction of the web or side edges of the paper. This is called the grain direction.A paper is called “grain long” if the grain is parallel to the paper’s long side.
When using a table saw never cut stock freehand the position of the stock must be controlled either by the fence or the?
Stock should be surfaced and at least one edge jointed before being cut on the saw. The position of the stock must be controlled either by the fence or the miter gauge. NEVER CUT STOCK FREE HAND.
What kind of cut should never be done on the radial arm saw?
Never clear small pieces while blade is moving. Never adjust saw or setup while saw is running. Never cross arms. Radial arm saws cut in a fashion that pulls the blade into the piece pushing the stock to the fence.
How must the saw blade be held after the cut?
4. Hold the saw firmly and lower the blade slowly into the material being cut. After the cut is completed continue to hold the blade in the down position, release the off/on switch, wait till the blade stops rotating and the raise the blade to the up position.
How does a planer work?
A planer is used to make a board that’s been jointed flat equal thickness from end-to-end.A flattened board is placed on the planer table (bed) and pushed in. The machine’s feed roller grabs the board and pulls it through and past a rotating cutter headset above the bed, which removes wood.
What is an advantage to using a planer?
The Benefits of Using a Planer
Planers are great tools for maintaining straightness on double surfaces and cutting wood with precision accuracy to the desired thickness. You can use a woodworking planer to create parallel surfaces and adjust the thickness of finished boards quickly.
How does a planer machine work?
A planer is a type of metalworking machine tool that uses linear relative motion between the workpiece and a single-point cutting tool to cut the work piece. A planer is similar to a shaper, but larger, and with workpiece moving, whereas in a shaper the cutting tool moves.
Contents