The temperature of the water in the heater is regulated by the adjustable surface mounted thermostat(s) located behind the jacket access panel(s).
Where is the thermostat located on a gas hot water heater?
On most gas water heaters, the gas control valve, which includes both a thermostat and a heat limiting device, are located on the outside of the unit, near the bottom.
How do you adjust the thermostat on a Rheem water heater?
Pull the insulation from the cavity behind the covers to expose the thermostats. Insert a small flat-head screwdriver into the slot on the thermostat dial. Rotate the thermostat to your desired temperature. Make sure to adjust both thermostats if your Rheem water heater has two access covers.
Do gas water heaters have two thermostats?
Many modern homes come with dual-element water heaters. A dual-element water heater uses two heating elements controlled by two separate thermostats.When it reaches a specified temperature, Rheem notes that it shuts off, and the lower heating element takes over, heating the rest of the water.
How do I know if my hot water heater thermostat is bad?
If you turn the hot water tap and cold water runs out, then the upper thermostat is damaged. But if the water is hot that becomes later becomes cold, then you have a damaged lower thermostat.
How do you reset the thermostat on a gas hot water heater?
To reset it, you’ll need to press the red reset button on the ECO, which is usually attached to the upper thermostat. When a water heater starts tripping the ECO repeatedly, it’s time to call a plumber for service.
Where is the hot water thermostat?
Thermostats are usually installed about one third of the way up the hot water cylinder. They measure the temperature of the water inside and if this falls below the required temperature (usually 60-65°C), the boiler will come on.
What setting should my Rheem water heater be on?
120°F.
Residential tank water heaters typically store between 20 and 80 gallons of hot water hot throughout, usually at the factory setting of 120°F. The temperature can be adjusted up or down by a control on the unit.
Why do some water heaters have two thermostats?
Most electric water heaters above 20 gallons have two thermostats that sense the temperature of the water in both the top and bottom of the tank. The upper thermostat is the boss and always tells the lower thermostat what to do.
What should my water heater thermostat be set?
The short answer: 120 degrees Fahrenheit. This is the preset thermostat temperature in most new water heaters, and it’s the recommended setting of the U.S. Department of Energy. At this temperature, harmful pathogens like the kind that cause Legionnaires’ disease are prevented from multiplying and may be killed.
How do you check a thermostat on a gas hot water heater?
How to Test a Water Heater Thermostat
- Switch the water heater’s power off.
- Remove the access panels and insulation so you can access the thermostats/elements.
- Using a screwdriver, set the upper thermostat on high, and the lower thermostat on low, by turning the dial in the middle.
- Turn the power back on.
How much does it cost to replace a water heater thermostat?
The average thermostat replacement cost is between $100 and $300. Most other repairs are equally affordable. There are two main types: gas and electric. A gas unit works by way of a gas flame while an electric one works using electric elements, or coils.
How do you reset a Rheem gas water heater?
Turn the water heater’s gas valve switch to the “OFF” position, wait for a few seconds and then flip the switch to the “ON” position to reset the system.
How do I know if my water heater thermostat is bad?
Since the upper thermostat controls the lower thermostat, when the upper fails, the lower never turns on. Lower Thermostat Failure – If your lower thermostat (or heating element) is defective, you’ll either notice the hot water is lukewarm or the hot water quickly runs out.
In some cases, the water heater reset button will repeatedly trip. This is a warning sign of a larger issue such as a faulty thermostat, loose wiring, corroded parts, a grounding problem, or a malfunctioning high limit switch.
Why is my gas hot water heater not heating?
No Hot Water Gas Water Heater. If a gas water heater isn’t heating, a common problem is usually that the pilot light has gone out. This may be caused by the gas valve, the natural gas supply, ormore likelythe thermocouple located next to the pilot light.
How does a gas water heater thermostat work?
The thermostat is a thermistor that responds to heat by producing a small electric current. The current increases when water temperature increases, and drops when temperature drops. Changes in the electric current cause gas control to turn ON and OFF. When gas control turns ON, it releases gas to burner.
Should both thermostats on water heater be set the same?
The majority of electric water heaters have two thermostats: an upper and a lower, located under two control panels. To ensure your electric water heater works as efficiently as possible, you should set both of the thermostats at the same temperature.
How long does it take for a Rheem water heater to heat up?
The average gas heater takes between 30 and 40 minutes to fully heat up the water in its tank. The average electric heater takes about twice as long as the average gas heater to fully heat up the water in its tank, so you can expect it to take between an hour and an hour and 20 minutes to heat up.
Should I set my water heater to AB or C?
The Department of Energy recommends setting your heater to 120 degrees Fahrenheit. That should be plenty hot enough for most uses in your home. Now, some water heater temperature controls come with settings that read A-B-C as opposed to numbers.
Contents