FLOOR CLEANING Press the power switch at the top of the canister to the I position to vacuum bare floors (straight suction only) or use Lift-Away® mode (see below). To vacuum carpets and rugs, set the switch to the II position to engage motorized brushroll.
Why does my shark vacuum not turn on?
Check for a clogged hose or filter; unclog the hose and replace the filter. Wait 45 minutes for the vacuum to cool; then plug in the vacuum. Turn the power switch to the “I-On” position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
Why is my Shark not picking up?
Clogged air filters can contribute to suction loss and be the cause of your Shark vacuum not suctioning. If you neglect the air filters for too long without cleaning them, dirt and debris can build up on their surfaces. The accumulated residue will block the airway, causing the vacuum to “choke up”.
Where is the on switch on a Shark vacuum?
1. Press the power switch at the top of the canister to the I position to vacuum bare floors (straight suction only) or use Lift-Away® mode (see below). To vacuum carpets and rugs, set the switch to the II position to engage motorized brushroll.
Why is my Shark Cordless not working?
Unplug your vacuum from the power source. Check to see if there’s a blockage in your filters and hose. Then, you should remove the clogs and wash the filters until it’s completely clean. Leave the vacuum to cool.
To reset the shark vacuum, put the Power button on the On-Off position and keep the vacuum unplugged. If necessary, clear the hose. Plug the vacuum in again after it cools completely.
The shark brush-bar reset button can be found on the underside of the vacuum.
How do I reset my shark ion vacuum?
Turn your machine upside down and find the power switch. Press it for 10 seconds, which triggers the factory reset process. Wait a few seconds before turning your Shark ION robot again.
How do I increase the suction on my Shark vacuum?
Shark vacuum suction problem quick tips
- At first, unplug your vacuum.
- Empty the dust cup and clear its dirt and debris.
- Remove the filters and clean filters with water.
- Check the airflow of your vacuum hose, end of the handle, and the front of the wand.
- Check brush roll for dirt or debris.
Can I wash Shark dust cup?
To clean foam and felt filters, simply tap off loose dirt, then rinse them under a tap. Only use water – do not use soap. Always let the filters air dry completely before reinserting them. You can also tap loose dirt off filters between washes as needed.
Why does my Shark Hoover keep spitting out dirt?
There are three places where clogs are most often found: behind the brush roller, the hose, and the dust cup air duct. Also, you might need to clean the HEPA filter. If the filter is dirty it could prevent the vacuum from blowing out any air which could be the reason the vacuum is blowing out dirt.
How do you remove the bottom of a shark rotator vacuum?
- Step 1 Roller Brush.
- Flip the base of the vacuum over to access the bottom.
- Remove the nine 16 mm screws using the Phillips #2 Screwdriver.
- Pull up on the cover and move it to the side.
- Remove the two 11 mm screws using the Phillips #2 screwdriver.
- Pull out the roller brush.
Why does my Shark Hoover smell of burning?
The main reason why a vacuum may be emitting a smell of burning rubber is a broken belt or an object is suck. Excess hair or fur caught around the roller brush can also cause this issue. Turn off your vacuum and let it cool before doing anything.
Can you wash the Shark vacuum canister?
Soak the canister in soapy water and wash it using your microfiber cloth. Rinse it in cold water and allow it to air-dry. Be sure the canister is completely dry before reassembly. This may take around 24 hours.
How often should I clean my Shark filter?
Wash your filters
We recommend you clean your Shark vacuum’s filters every month – but always remember to let them air dry thoroughly before replacing them.
Contents