Where Is Reset Button On Blink Outdoor Camera?

There is a small reset button on the bottom of the camera. Use the reset button if your camera isn’t connected to the Internet or when you want to connect it to a Sync Module. You can also power cycle the Mini or delete and reinstall it in the Blink app just like you would with the Sync Module.

Where is the reset button on Blink Sync module?

The Sync Module has a physical reset button located next to the USB port on the side of the device (pictured below). This button should only be used to put your Sync Module into setup mode. Pressing this button will bring your system offline until you reconfigure your Sync Module.

How do I get my blink camera back online?

If your camera is in this state, you may need to try the following troubleshooting steps to get that camera back online. Power cycle your camera by removing the batteries for 5 seconds and reinserting them. Wait 30 seconds, then try using that camera again. Move the camera closer to your Sync Module.

How do I reset my blink camera Wi-Fi?

From the the Camera Settings screen scroll down to the bottom and tap Change Wi-Fi. In the Change Wi-Fi screen, follow the instruction to “Press and release the reset button on the camera until red and blue lights flash. When ready, the lights will display: Blinking Blue, Steady Green.”

How do I reset my Blink XT camera?

Grab a pin or paperclip as you’ll need this during the process. Remove both batteries from the camera for 10 seconds. Insert both batteries back into the camera. IMMEDIATELY press and hold the reset button just to the right of the yellow Lithium Only sticker for 10 seconds.

Why are my Blink cameras not working?

If one of your Blink cameras isn’t responding, you may see error messages like “Camera Busy” or “Thumbnail Failed”.Wait two minutes for Internet service to be restored, then try using your camera again. Power cycle your camera. To do this, remove the batteries for 10 seconds and reinsert them.

What happens if you delete Blink Sync module?

Cameras attach to a system through the Sync Module, and the Blink app manages systems. When you delete a system, all of the devices on that system are also deleted.When you delete individual devices, remember that the “system” still exists even with no devices attached.

Why would my blink camera go offline?

If you receive a “Camera Offline” notification that “Your Blink Mini is offline”, it means the Blink servers no longer have communication with the camera.The first, is to check the Wi-Fi internet and the power supply, then check the camera power connection.

How do I fix blinking Wi-Fi?

Restart your device, or try switching the Wi-Fi setting off and on again to establish a connection. Make sure your mobile device is within range of your router or access point. Check that your router and any access points are powered on. Restarting your Wi-Fi router may also resolve this issue.

How do I reset blink camera for new owner?

How to Transfer Blink Camera to a New Owner

1. To completely delete the system, you will need to log into your Blink account on the app.
2. Select the name of the system you wish to delete.
3. Next, you will tap on Delete System.
4. The app will return you to the Settings screen.

Can I delete my Blink account and start over?

Note: Deleting the account removes the account creation date. Changing the email address to a new user, on an existing account, will retain the original creation date. Click here to learn more about how to change the Blink account email address.

Can you use Blink without WiFi?

Blink cameras can’t operate offline and require a 2.4 GHz Wi-Fi Internet connection.Blink systems minimally require a high speed connection of at least 2 Mbps upload speed. Wi-Fi is also important for Blink cameras that need to connect to a Sync Module on the same Wi-Fi network.

Do Blink cameras record without WiFi?

Hello! Blink cameras cannot function without an active WiFi connection or an online Sync Module.Blink cameras cannot function without an active WiFi connection or an online Sync Module. If internet connectivity is lost or if the Sync Module is powered off, the system will go offline until it both are restored.

Does Blink camera connect to WiFi or sync module?

Blink’s original Indoor, XT, and XT2 cameras will only connect to the same Wi-Fi SSID that the Sync Module is connected to. To set up these cameras with an extender, be sure to rename the Wi-Fi extender SSID to be the same the main Wi-Fi network, and use the same password.