when installing batteries in an aircraft, shorting of the batteries can be avoided by:
- insulating the terminal posts during installation.
- neutralizing and flushing the battery compartment.
- installing nonconductive battery hold-down clamps.
What safety precautions should be taken when handling batteries?
Precautions
- Always handle batteries with care.
- Never overfill with acid.
- Always store upright.
- Never allow children access to a battery.
- Always charge in a well ventilated area.
- Never allow battery vents to become blocked.
- Always wear eye protection.
- Always wear protective clothing.
What precautions should be taken when working with and charging lead-acid batteries?
Lead-Acid Battery Safety Precautions
Wear acid-resistant goggles/face shield, gloves, and if available, an apron, when recharging or handling lead-acid batteries, Keep lead-acid battery vent caps securely in place. Rinse the affected area immediately with large amounts of water if acid gets on your skin.
When installing multiple batteries on aircraft they are connected in?
Connecting a battery in parallel is when you connect two or more batteries together to increase the amp-hour capacity, with a parallel battery connection the capacity will increase, however the battery voltage will remain the same.
How can you prevent the spillage of electrolyte from an aircraft storage battery?
The cell cover is provided with two holes through which the terminal posts extend and a threaded hole into which is screwed the vented cell cap. When the cover is placed on the cell, it is sealed in with a special sealing compound. This is to prevent spillage and loss of electrolyte.
How can battery hazards be prevented?
When working with batteries, prevent exposure by wearing personal protective equipment (PPE). Never attempt to handle car batteries with bare hands. Always use sufficient protective clothing and accessories such as gloves and safety glasses when checking or changing batteries.
What are the 6 safety precautions?
General Precautions
- Your safety is your personal responsibility.
- Always follow the correct procedures.
- Never take shortcuts.
- Take responsibility and clean up if you made a mess.
- Clean and organize your workspace.
- Ensure a clear and easy route to emergency exits and equipment.
- Be alert and awake on the job.
What is topping up procedure for batteries?
Topping up best practice
It is best practice to top up batteries immediately after charging when batteries are fully charged. Check the water level each time you charge and if the electrolyte isn’t covering the element by 5mm, add distilled or demineralised water.
What are the main safety requirements of the battery charging room?
It should have a full ventilation system, including hydrogen gas detectors, to compensate for battery gassing. All battery stands should be coated to withstand acid, and rollers should be spark-proof. Floors should be extremely flat and level concrete, with an acid- and impact-resistant coating.
Battery acid: The electrolyte in a battery is corrosive and can burn skin or eyes, eat holes in clothing, or even etch a concrete floor. B. Flammable gases: Batteries emit hydrogen gas, which is flammable. It ignites easily and can cause a fire or explosion if allowed to accumulate in a small area.
What happens when batteries are connected in parallel?
When batteries are connected in parallel, the voltage remains the same, but the current that can flow in the circuit increases.
Can you connect two different size batteries in parallel?
As long as they are the same type of battery there are no problems. Don’t mix FLA, AGM or gel batteries in a parallel set up. They have different charge and discharge profiles. They will charge and discharge according to capacities.
What are the precautions to be observed during removal and installation of aircraft battery?
This condition may normally be avoided by insulating the terminal posts during the installation process. Remove the grounding lead first for battery removal, then the positive lead. Connect the grounding lead of the battery last to minimize the risk of shorting the hot terminal of the battery during installation.
How do you maintain aircraft batteries?
The battery should be removed from the aircraft and put on a constant current top charge at the C/10 rate until all the cells have reached at least 1.55V each, and for the time specified in the maintenance instructions. This is when we adjust the electrolyte in each cell by adding distilled water as required.
When a nickel cadmium battery begins gassing while connected to the battery charging circuit what should be done?
The voltage used during charging, as well as the temperature, determines when gassing will occur. To completely charge a NiCad battery, some gassing, however slight, must take place; thus some water will be used. The chemical action is reversed during discharge.
What is battery hazard?
Why Batteries ARE Hazardous Waste
They contain substances such as sulphuric acid, mercury, nickel, cadmium, or lead, as well as other dangerous materials that can give batteries a variety of hazardous properties. These hazardous substances can also lead to a fire or explosion risk.
What is battery safety?
The batteries that power many of your household devices and children’s toys contain harmful substances, like acids, that can cause serious injury and even death if swallowed by a child. They can also pose a risk of fire or explosion.
How you will prevent the danger causes by battery when you are onboard the vessel?
1) Providing proper ventilation inside the compartment. 2) By preventing any source of ignition. Moreover, the ventilation is provided with the help of ventilation fans. The ventilation arrangement should be such that there is no accumulation of hydrogen in the space.
What are the 4 general safety rules?
Basic Safety Rules
- STAY ALERT – and stay alive.
- WEAR THE RIGHT CLOTHES – work clothes should fit properly.
- USE THE RIGHT TOOLS – if you need a hammer, get a hammer.
- LEARN HOW TO LIFT – Lifting takes more than muscle; it is an art.
What is general safety rules?
Seven Basic General Industry Safety Rules
- Keep work areas clean.
- Use the proper tool for the job.
- Always wear the proper PPE for the work task.
- Never work on live equipment.
- Make sure chemicals are properly labeled and stored.
- Communicate hazards to other personnel.
- Stop work when needed to address hazards.
What are the safety rules of electricity?
Here are some tips to prevent accidents & electrical oversights:
- All electrical equipment should be in proper working condition.
- Main Power Off.
- Warm & Cold Power Outlets.
- Fire Extinguisher.
- Ground Older Appliances.
- Expert Intervention.
- Rooms with running water need to be equipped with Ground Fault Circuit Interrupters.
Contents