The hot water cylinder thermostat controls the temperature of water that comes out of the taps. In hard water areas it is recommended that the thermostat on the immersion heater is set to 50°C. If you have a twin immersion heater the top element should be set to 50°C and the lower one to 60°C.
What temperature should my hot water tank be set at UK?
60-65?C
A domestic hot water cylinder thermostat should be set at 60-65?C. This is high enough to kill off harmful bacteria such as Legionella. If you set the thermostat much higher than this the water that comes out of the taps will be too hot and there’ll be a risk of scalding.
Can you adjust the temperature on an immersion heater?
Whether the water from an electric immersion water heater is too hot or too cold, it can be easily adjusted as it is thermostatically controlled. The protective cap over the connections to the immersion heater is normally held in place by a nut or screw.
Is it cheaper to leave immersion heater on all the time?
It’s better to leave the hot water heater on all the time, rather than turning it on and off.Your immersion heater or boiler will heat up hot water which is stored in a tank. As long as the tank has a good insulating jacket, it will keep the water hot all day, without needing to be constantly reheated.
What temperature should I set my hot water cylinder to?
60 degrees
The temperature of your storage water tank should be kept at a minimum of 60 degrees at all times (but not delivered to taps at above 50 degrees). This is to prevent legionnaires disease which can become very serious. Legionnaires can be contracted by inhaling droplets of contaminated water.
What temperature should hot water be on combi boiler?
60 degrees
Modern boilers will have a digital dial where you can set the output temperature. For combi boilers it is recommended to set the output temperature for the radiators at 75 degrees and the water temperature at 60 degrees.
How do I turn down the temperature of my hot water?
Gas or electric water heaters
- Start by turning off power to the water heater at the circuit breaker.
- Find the access panel for the thermostat(s) and use a screwdriver to remove the panel.
- Peel back the insulation.
- Use a flathead screwdriver to adjust the thermostat up or down.
How long does an immersion take to heat up?
The immersion heater is connected to the mains electric via a cable and has its own on/off switch. When the heater is turned on, electricity heats the metal element and this heat passes to the surrounding water. It can take 1-2 hours for the water in the cylinder to reach your desired temperature.
Why is my immersion heater overheating?
If the hot water is too hot, there’s a likelihood the cylinder is overheating, most probably as a result of the immersion heater thermostat not shutting down.For direct cylinders where the water’s ‘scorchio’, the unit may have been incorrectly wired. You’ll need to correct the wiring errors to fix the problem.
Does an immersion heater use a lot of electricity?
Heating water using electricity is more expensive than heating water with gas. A typical immersion heater uses three kilowatts of electricity an hour, so it will cost the average house about 50p an hour to run.
How Long Does immersion take to heat water for shower?
Initial reports are that while immersion heaters can take up to an hour to heat enough hot water for a bath or shower, the KRIB can do so in just six minutes.
What happens if you leave the immersion on?
The main problem with leaving an immersion on constantly is that the immersion thermostat will be constantly switching on and off. After so many hours the thermostat will give up, causing one of two problems. Problem one is that the immersion will not work.
What is the ideal water temperature?
The best temperature for drinking water is room temperature (20°C / 68°F) for maximum flavour, or chilled cold (6°C / 43°F) for maximum refreshment. However, there are different types of water, a myriad of reasons we drink it, and varying personal preferences.
What temperature should hot water be set at combi boiler UK?
The best setting for combi boilers is often recommended as 75°C for central heating and 60°C for domestic hot water. Turning down the temperature of the domestic hot water is particularly helpful as it can greatly reduce any risk of scalding.
Is 60 degrees water hot?
In general, hot water is 130 F (54.4 C) or above. Warm water is between 110 and 90 F (43.3 to 32.2 C). Cold water is generally between 80 and 60 F (26.7 to 15 C).
How long does water stay hot in tank?
As an estimate, the water in your tank should stay hot for a day or two. The larger the tank, the greater the heat loss will be, and it depends on the quality of your tank as well as the form of insulation you have.
How do I know if my immersion heater is on?
How do I know if my electric immersion is on? The first thing to do is follow the wire (where possible) from the immersion heater element at the top of the hot water tank to the wall, where hopefully you will see a switch. If it is on, flick it off!
Should the top of my water heater be hot?
Even though it’s designed to boil water, your water heater shouldn’t get so hot that you can’t touch it. Water heaters are designed to be well insulated so that heat stays in. A water heater that gets too hot could have one of several issues, including: A blocked flue.
How do you know if your water heater is going to explode?
The signs your water heater is going to explode are leaking tank water, the faulty pressure relief valve, cloudy water, popping noise, and the lack of hot water. A hot water heater explosion can lead to death, physical injury, and serious damage.
Why does my immersion heater have 2 thermostats?
Modern immersion heaters have a second thermostat. This is not adjustable, but switches the element off if the water reaches a pre-determined high temperature, usually around 85 degrees.
Is it cheaper to leave an immersion heater on 24 7?
Switch on as required
This topic comes up in discussion forums all the time, but it is not cheaper to leave the immersion on all of the time, rather than to switch it on and off as required. Even with a good lagging jacket, the cylinder will lose heat and cost more to reheat the water to the optimum temperature.
Contents