The voltage dropped by a resistor is given by Ohm’s Law: V = I R. So if you know exactly how much current your device will draw, you could choose a resistor to drop exactly 7.5 V, and leave 4.5 V for your device, when that current is run through it.
What resistor do I need to reduce voltage?
To reduce voltage in half, we simply form a voltage divider circuit between 2 resistors of equal value (for example, 2 10KΩ) resistors. To divide voltage in half, all you must do is place any 2 resistors of equal value in series and then place a jumper wire in between the resistors.
What resistor do I need to drop 12v to 3V?
take a 12v 4ohms potentiometer where the pointer will be adjusted at 3 ohms so that the voltage at last 1 ohm will be 3v. use a resistor in series with a 3 V zener diode to ground.
What resistor do I need to drop 12v to 5V?
12v to 5v converter using a voltage divider:
Components required: One 12v battery, 1.8k resistor, 1.3k resistor, connecting wires.
How do you reduce 5V to 1.5 V with a resistor?
This is a USB 5V to 1.5V/3V Step-Down Converter Circuit. It is used instead of a normal AA battery. In the circuit, we use LM317 DC voltage Regulator. To reduce the 5V input voltage from USB Port to the 1.5V at 1.5A maximum output.
5V to 3V Converter circuit.
| Vout | R1 | R2 |
|---|---|---|
| 3.08V | 150Ω | 220Ω |
How do you reduce 12 volts to 9 volts?
To reduce a 12V circuit to 9V, place two resistors in series within the circuit. Find the difference between the two voltages (12V – 9V = 3V) to determine the total amount of resistance needed.
What size resistor do I need?
A rule of thumb is to find a resistor with twice the power rating. Here I would choose a 250 mW resistor since those are the most standard ones. Usually, you can just use the cheapest resistor you can find with the correct power rating.
What resistor do I need to drop 24V to 12V?
Registered. The resistor you need is 120 ohm power rated at 2W, that is the most common value I would use.
What resistor do I need to drop 12V to 6v?
It’s possible to step 12 volts down to 6 volts by incorporating a pair of 10,000-ohm resistors into the circuit.
What resistor do I need to drop 5V to 3V?
The simplest possible step-down circuit is a resistive divider. Drive your 5V output into a chain of resistors, from which you tap your 3.3V logic input. A chain consisting of a 2.2k and a 3.3k resistor should produce a 3V output from an applied 5V input.
How do you step down 12 volts to 5 volts?
In a circuit with multiple electrical resistors, the voltage will drop at each resistor electrical joint. This can be useful if you need to obtain five volts from a 12-volt power source. Cut two pieces of electrical wire. Strip ½ an inch of insulation from the ends of each wire.
How do you reduce voltage output?
Two ways to reduce a 12-volt system to 4 volts are to use voltage dividers or Zener diodes. Voltage dividers are made from resistors placed in series. The input voltage is divided into an output that depends on the value of the resistors used.
Does resistor reduce voltage or current?
Resistors don’t reduce current and voltage instead it opposes flow of current and produce drop in voltage across the terminals.
How do I reduce 3.7 V to 3V?
By using a step-down buck converter, the 3.7V can be brought down to 3V. But beware of the current that is running through the circuitry in the car. By using a buck converter with a 5Amp current rating, the current will be constant and the car will not be damaged.
How do you reduce voltage from 18v to 12V?
To reduce the voltage variation you could configure two resistors as a voltage divider. The lower shunt resistor (R2 in the circuit below) helps to hold the voltage down under light load, and permits a lower value for the upper series resistor (R1) which reduces voltage drop under heavy load.
How do you reduce 12 volts to 7 volts?
If it is less than 1A, you can use a adjustable voltage regulator (LM317) to make a regulated 7v. But the regulator will need a heat sink to dissipate 5 Watts of power (12–7)×1=5 Watts. The simplest way to do this is using a 7V zener diode and a power resistor.
How can I reduce 12V to 10v?
- To drop voltage from 12V to 10.5V using resistors then you can use 2 resistor in series.
- R2/(R2+R1) × 12V = 10.5V.
- Solving the equation gives:
- R2=7×R1.
- Therefore if you choose R1 to be 4.7kOhm, R2 wil be 33kOhms.
How do you reduce a 24v to 5V with a resistor?
You will require: Resistor (R1)190 Ohms – 2W or greater and (R2)50 Ohms (0.6W or greater). If you do not have the exact values stated then you will not get exactly 5 volts. Make sure that your load (what you want to use the 5v for) is a lot higher then 50 Ohms.
How do I choose the right resistor?
Resistor selection requires three steps:
- Determine the resistance and the watts to be dissipated by the resistor.
- Determine the proper “Watt Size” (physical size) as controlled by watts, volts, permissible temperatures, mounting conditions and circuit conditions.
What happens if you use the wrong resistor?
There is no harm. But it will not give you extra advantage. On the other hand, higher wattage resistor costs you more and the resistor demands more space on the board, being thick. Resistor is like a current limiter.
What is 1k resistor?
So, a 1k Ω resistor has a value of 1,000 ohms and the number we will code is 1,000.
Contents