The standard sized bore hole is 2 1/8″ in diameter. Through the edge of the door there is a 1″ cross bore that extends from the edge of the door through the bore hole. This cross bore is where the latch is installed. In addition to the two cross bores, a door can be prepped for one of 3 different types of latches.
https://www.youtube.com/watch?v=MdXyOCU8wOU
How big is a door latch hole?
2 1/8 inch
The latch bore is the small hole on the edge of the door for the latch itself. The standard measurement for a bore hole is 2 1/8 inch in diameter and the standard measurement of a cross bore is 1 inch in diameter.
What size hole do you drill in a door for a door knob?
A standard door knob hole is 2 1/8 inches in diameter. This won’t have the best fit on older doors because their holes are usually smaller. If you’re looking to change or replace older door knobs, you need to re-drill the door to fit the current standard size.
Which hole saw is the typical size to install the latch through?
2 1/8-inch
3 Bore the doorknob hole through the face of door using a 2 1/8-inch hole saw; drill halfway through from each side. 4 Use a 1-inch hole saw to bore latch hole in door edge.
Are lock holes for doors a standard size?
2-1/8
Standard Door Measurements
Lock Bore The diameter of the hole for the lock body. The standard bore is 2-1/8. Many older doors had bores that were been smaller. Most of the current locks require the standard 2-1/8 bore.
Are door knobs one size fits all?
Choosing the right door knob is more than simply a matter of appearance.The standard size for a door knob diameter is either 2 3/8 inches or 2 3/4 inches and these knobs will usually fit doors that are anywhere between 1 3/8 inches to 1 3/4 inches thick.
What size is a deadbolt hole?
2 1/8-inch
Be sure to use the correct size drill bits specified in the lock set instructions, though most standard deadbolts require a 2 1/8-inch hole saw for the lock bodies and a 1-inch spade bit for the sliding bolt assembly.
What is the cross bore on a door?
The cross bore is the small hole on the edge of the door. The door latch is inserted into the cross bore first. The latch goes through into the large bore hole and then the door knob is mounted The backset is the distance from the edge of the door to the center of the large bore hole.
What are spade bits?
Also commonly known as paddle bits, spade bits have a wide, flat blade.The flat, broad blade of a spade bit has a pilot point attached to a 1/4-inch diameter shank that can be chucked into both regularly-chucked drills and quick-chuck impact drivers.
What is the door latch hole called?
The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt. The diameter of the latch bore is generally 1 to accommodate bolts from either mechanical or electronic locksets.
What are Forstner drill bits?
Forstner bits are unique in their ability to drill overlapping holes, notches on the edges of a workpiece, and angled holes on the face of a workpiece (pocket holes, for example). The bit will cut whether or not the center spur is engaging the workpiece.They manufacture a unique Forstner-style bit in France.
How do I know what size door lock I need?
You can work out the size of the lock by measuring the distance from the edge of the door to the centre of the door handle or knob. This measurement will give you the approximate size of the backset which will allow you to identify which size lock or latch you have.
Are door handles standard?
The industry standards are usually 44 mm/ 57mm / 82mm / 107mm / 130mm. Ideally you will try and choose the backset measurement that sites the door handle in the middle of the door stile. A shorter backset is recommended if you’re using a glazed door.
Is every door knob the same?
There are two main categories of door knobs: those made for doors inside a house, and those made for doors on the outside of a house. Within each category, there are a number of subtypes of knobs to consider as well.
Is it easy to install door knobs?
But, while the parts of a door knob may seem complex at first, installing a new door knob can be a simple DIY project. You don’t need to hire a home repairman to change or add a door knob. As long as you’ve taken your door’s measurements and purchased the right knob, you can fit it in securely all by yourself.
How do you make a strike plate hole bigger?
You can move the strike plate up or down and in or out. Use a sharp chisel to enlarge the strike plate mortise. Then hold the strike plate in place and drill new 1/16-in. holes for the screws.
How thick does a door need to be for a deadbolt?
The door’s thickness should be between 1-3/8 and 1-3/4 inches. Most deadbolts fit doors in this range.
How much space should be between door knob and deadbolt?
5 1/2"
– Your door must have a minimum of 5 1/2″ between the center of the deadbolt crossbore hole and the center of any other door latch below the deadbolt.
Are all door latches the same?
In the United States, there are two common backsets for residential door locks: 2 3/8 inches and 2 3/4 inches. Pack your locks with a 2-3/8-inch or 2-3/4-inch latch, depending on which backset you specify.
What tools do you need to install a door knob?
Tools
- Drill / Driver.
- Screwdriver.
- Utility Knife.
- Wood Chisel.
- Tape Measure.
- Hammer.
- Sawhorses.
- Door Lock Installation Kit / Hole Saw Kit.
Contents