What Is The Push Side Of A Door?

Secure side.
Secure side is the “PUSH” side of door. Secure side is the “PULL” side of door.

Which side of the door does a closer go on?

Closers should be mounted on the interior side of exterior doors, and for interior doors the closer should be mounted on the side of the door that is least exposed to public view. A parallel arm closer is mounted on the push side of the door, and the arm is parallel to the frame when the door is closed.

Do door closers push or pull?

Door closers with a regular arm will be mounted on the pull side of the opening. The closer body is mounted to the top of the door and the closer arm is attached to the face of the frame head.

What is the door closer called?

An automatic door closer, more often called a “door opener”, opens the door itself, typically under the control of a push button, motion detector or other device, and then closes it as well, employing a motion or proximity detector to determine when it is safe to close the door.

What is the minimum clearance required for a front approach on the push side of a door?

Front approaches to push side of swinging doors, if not equipped with latch and closer, shall have maneuvering space that is the same width as door opening and extends 48 inches (1220 mm) minimum perpendicular to the doorway.

Are door closers handed?

For Door closers & Pivots
Door closers, pivots and pivot sets are supplied as LH or RH only. The hand is determined from the push side of a door. The hand of a closer or pivot is the same as the hand of the door. When using a corner bracket, the hand of the closer changes to the hand opposite that of the door.

Are all door closers hydraulic?

All modern door closers can be divided into two categories—hydraulic (liquid) models and pneumatic (air) units. Basically speaking, both types work on the same general principle. As the door is opened, a powerful spring on the inside of the closer is compressed or tightened.

What is a door arm?

Door closers with regular arms are usually mounted on the pull side of the door, where the closer body is mounted to the face of the door and the closer arm is attached to the face of the frame at the head. Regular arm door closers allow doors to travel up to 180 degrees.

What are different types of door closers?

There are three different types of door closers: Regular Arm, Parallel Arm and Top Jamb Mount. Each of these function in a similar way, but they are installed on different sides of the door. The amount of ceiling clearance needed varies depending on the door closer.

What is in a door closer?

A door closer is an adjustable and spring-loaded mechanical arm that closes a door automatically after it has been opened. Door closers are usually filled with hydraulic fluid, which dampens the door swing and controls its operation. Installing a door closer adds a level of control to your door’s safety and security.

What is a door puller?

noun A handle used for opening or shutting a door.

What is the most common type of door closer?

Types of Door Closers
The most common door closer used in commercial buildings today are the Modern Type closers, with or without the cover. These closers all work in essentially the same way. As the door is opened, a spring is loaded with tension.

How much space should be on each side of a door?

Check the door fit. Ideally, there should be a gap of about 1/8 inch at the top and along each side, and about 3/8 inch at the bottom.

What is ADA knee clearance?

Where knee clearance is required under an element as part of a clear floor space, the knee clearance shall be 11 inches (280 mm) deep minimum at 9 inches (230 mm) above the finish floor or ground, and 8 inches (205 mm) deep minimum at 27 inches (685 mm) above the finish floor or ground.

Do all entrances need to be accessible?

All entrances and exterior and interior exit doors regardless of the occupant load shall be made accessible to persons with disabilities.Separate facilities are required where provided for the non disabled.

What is a non handed door closer?

Question. NON-HANDED. Resolution: Closer or part designed for both right and left hand swinging doors.

How do you tell the hand of a door?

First, the SIMPLE WAY to determine door handing…
IF YOU ARE REPLACING AN EXISTING DOOR: With the door open, stand with your back against the hinge jamb. If your left hand is nearer the doorknob, then the door is LEFT-HANDED. If your right hand is nearer the doorknob, then the door is RIGHT-HANDED.

How do you determine if a door is LH or RH?

If the hinges are on your Left side, and the door is pushing away from you, it is a Left Hand (LH) Swing. If the hinges are on your Right side, and the door is pushing away from you it is a Right Hand (RH) Swing.

How do pneumatic door closers work?

In a pneumatic closer, for example, there is an air tube inside the cylinder. When the door is opened, this tube fills with air as the piston extends. When the door is released, the internal spring begins to pull the door shut.

Is hydraulic door closer better than pneumatic?

Both options offer speed and resistance options. The only major difference is that pneumatic doors are cheaper and suited to light and medium doors. Hydraulic closers are stronger and suited to heavier doors.

What does S and L mean on a door closer?

Some models have separate adjustments for “sweep” (“S”), which is the speed with which the door moves when it starts closing, and “latch” (“L”), which is the speed it moves when it is about to close.High backcheck tension prevents people from damaging the wall when they push the door open.