Bore holes are the holes in the door that house your door hardware and allow it to be installed.The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt.
What does no bore mean on a door?
We refer to the round holes where the door lock is installed as bore holes (brush up on your door hardware terminology here.) Most doors have one, two or three bore hole. If the door has no bore holes, you can simply install a non-turning or dummy knob or lever that serves as a decorative door pull.
How do you measure a door bore?
Measure the bore hole.
Measure across the circular hole at its widest point, i.e. start at the bottom of the hole and pull the tape until you hit the top of the hole. There’s your diameter.
What are the different parts of a door lock called?
The main parts of a door lock are the cylinder, bolt, box and strike plate. It’s useful for any DIY-er to know how things around the home operate.
What does bore her mean?
transitive to make someone feel impatient or dissatisfied, especially by talking to them about things that are not very interesting. I hope I’m not boring you. bore someone with something: I won’t bore you with all the details. Synonyms and related words.
What is a non turning door knob?
Half dummy door knobs are non-locking door knobs that don’t have to be rotated or turned when opening or closing a door. Instead, you simply pull on the door to open it. Half dummy door knobs are mainly used on double doors that close side-by-side, such as on cabinet and wardrobe doors.
What are spade bits?
Also commonly known as paddle bits, spade bits have a wide, flat blade.The flat, broad blade of a spade bit has a pilot point attached to a 1/4-inch diameter shank that can be chucked into both regularly-chucked drills and quick-chuck impact drivers.
What size hole do I drill for door latch?
The standard sized bore hole is 2 1/8″ in diameter. Through the edge of the door there is a 1″ cross bore that extends from the edge of the door through the bore hole. This cross bore is where the latch is installed. In addition to the two cross bores, a door can be prepped for one of 3 different types of latches.
Are door handles universal?
Door levers are left-handed, right-handed or universal. To determine what you need, look at the door from outside the house or room. If the hinges are on the left, look for a left-handed or universal lever. If the hinges are on the right, you need a right-handed or universal model.
Are door handles standard?
The industry standards are usually 44 mm/ 57mm / 82mm / 107mm / 130mm. Ideally you will try and choose the backset measurement that sites the door handle in the middle of the door stile. A shorter backset is recommended if you’re using a glazed door.
What is a backset on a lock?
The backset is the distance from the edge of the door to the spindle mechanism on the latch. Usually for a 63mm case measurement it will have a 44mm backset and for a 76mm case measurement will have a 65mm backset.
What is a strike plate on a door?
Strike Plate
This is the plate the latch-tongue, or deadbolt-tongue will connect with. It should sit flush with the door jamb. Any passage or privacy set needs to have a strike plate for the door to latch. Additionally, deadbolts need a strike plate to properly lock.
What is the inner part of a door knob called?
Cylinder
The Cylinder: Also called the body, this is the part where the key is inserted. When it is locked, a series of spring-loaded pins are engaged by the cylinder. This keeps the cylinder from turning. The Bolt: Also called the latch, the bolt engages the inside of the door.
What is a door cylinder?
The cylinder is the locking mechanism of an entry door set. It may be integrated with a the deadbolt of a mortise lock or mounted independently as part of a separate deadbolt.One can secure the door from inside, as well as exit the house without a key, making this the most popular option.
What bore means?
: one that causes weariness and restlessness through lack of interest : one that causes boredom: such as. a : a dull or tiresome person His friends are a bunch of bores. b : something that is devoid of interest The lecture was a total bore.
What does it mean to bore a child?
The verb bear is sometimes used to describe the act of giving birth.Have is more common when talking about giving birth: She bore twelve children in twenty-two years. (or, more commonly, She had twelve children )
How do you use the word bore?
(1) Despite everything, she bore her former boss no animosity. (2) The sword bore through her breast. (3) She bore witness to his patience and diligence. (5) This drill can bore through rock.
What is a Georgian knob?
Schlage Georgian doorknobs have a simple, elegant design with a squashed round shape with a subtle recessed circle design in the end.Schlage door knobs are packed with an adjustable latch that will accommodate doors prepped for drive in latches as well as latches with faceplates.
What is the difference between passage and dummy door knobs?
The main types of door functions are Passage (doors that don’t require locking), Privacy (a door that can be locked by a button on the inside), Dummy (has no mechanical latch and acts only as a pull), and Interior Mortise (door with an active latch with skeleton key lock).
What is a UL function on door knob?
UL develops standards by which they test door hardware to verify that it meets certain safety requirements during use, or in the event of a fire or other circumstances. Not all locks are UL listed. In fact, most residential locks are not.
What is the main disadvantage to boring holes with spade bits?
What are the disadvantages of using a spade bit? Spade bits cause tear-out (splintering) when drilling all the way through a wooden workpiece unless you use a sacrificial piece of wood as a backing. They need to be spun too quickly to be used in hand-powered drills.
Contents