What Does Pr Mean On A Spa?

Master Spas Diagnostic and Troubleshooting Codes

Alpha Messages Meaning
Pr This message is displayed when your hot tub is first powered on.
–F or –C Temperature unknown.
Temperature not current in Economy or Sleep mode.
Ecn The hot tub is in Economy mode

How do you fix the PR code on a hot tub?

Pr or PRIMING MODE TAKES 4 MIN Message
The Spa has just been powered up and is in Priming Mode for 4 Minutes. Pumps and Blower can be turned ON and OFF to remove any Air from the Heater.

What does PL mean on my hot tub?

Panel Lock To lock or unlock the control panel, press ‘Set Temperature’ then ‘Light’. When locked, the display will alternate “PL” with the spa temperature.. Temperature Lock To lock or unlock the temperature set-point, press ‘Set Temperature’ then ‘Blower’.

What are the different modes on a hot tub?

Most Balboa hot tub control systems have three operating modes: Standard, Economy and Sleep. These modes affect the times at which the hot tub will heat, and therefore affect the overall power consumption.

What does PR mean on a hot tub control panel?

Master Spas Diagnostic and Troubleshooting Codes

Alpha Messages Meaning
Pr This message is displayed when your hot tub is first powered on.
–F or –C Temperature unknown.
Temperature not current in Economy or Sleep mode.
Ecn The hot tub is in Economy mode

What does PR mean on Beachcomber hot tub?

priming mode
Beachcomber Hot Tub Error Codes

Message Meaning
Pr This happens when the hot tub unit is actuated for the first time; eventually it goes into priming mode
–F / –C Means unknown temperature.
Std/ St STANDARD Means hot tub unit is functioning in Standard Mode.
Ecn/ Ec ECONOMY Means hot tub unit is functioning in Economy mode.
See also  Is Tiered Electricity Better?

Why is my hot tub saying E02?

Is there an E02 error code displaying on your Lay-Z-Spa pump? This means your Lay-Z-Spa pump is experiencing a water flow issue.To clean the filter cartridge use luke warm water, run the filter cartridge under the water until the water runs clear. Do not use any detergent, washing up liquid or other chemicals.

What is SPA code?

An SPA is sometimes referred to as a single-page interface (SPI). A single-page application may retrieve all of the application’s HTML, JavaScript, and CSS code on the initial load or may load resources dynamically to update in response to user interaction or other events.

What temperature should a hot tub be when not in use?

We always recommend keeping the temperature at 38°C, not only will this keep you warm, it also helps to protect your hot tub as the heat generated stops your power pack from freezing over. Make sure to always keep the cover on when you’re not using it, so the heat doesn’t escape.

What temperature should I leave my hot tub on?

Your hot tub factory settings will be at 38 degrees, but body temperature of 37 degrees is a generally good start for your hot tub. It’s regarded that women tend to like it slightly hotter at 38 – 39 degrees.

What setting should hot tub be on?

The majority of hot tub users prefer a water temperature in the range of 100°F-102°F. 104°F is the standard maximum temperature, which some users also prefer. Always consult a physician before getting in the hot tub while pregnant.

See also  How Do You Change Led Light Bulbs?

Should my hot tub be in ready or rest mode?

*Ready mode is recommended during the winter season to maintain constant warm temperatures and prevent freezing. To save energy but also maintain heat, set the spa to the lowest temperature possible in Ready mode.

Why is my hot tub saying change filter when I have?

As you may have guessed, this code appears when you’re hot tub is having flow problems. You might see this code if your jets are misbehaving. Check for blockages, and clean or replace your filter. If that doesn’t help, check to see whether your circulation pump has power going to it.

Where is the pressure switch on a Beachcomber hot tub?

The Pressure Switch on a hot tub or spa is a pressure sensor that is mounted onto the heater housing, or very close to the exit point of the heater. It’s sole purpose is to shut off the heater if low pressure (low water flow) occurs.

How long do Beachcomber Hot Tubs last?

The lower quality hot tubs only last up to 5 years before needing to be replaced. If you purchase a Beachcomber, your hot tub is built to last as long as you need it to! Around the country, there are Beachcomber hot tubs that are over 15 years old and still running like new!

How do I reset my hot tub control panel?

How to Reset a Spa Heater

  1. Locate the spa’s high-limit reset. This is a red button found on many spa packs.
  2. Press the high-limit reset button.
  3. Turn on your spa and observe its operation.
  4. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
See also  Is Comfortmaker Furnace Good?

What does EO2 mean?

EO2

Acronym Definition
EO2 Equipment Operator Second Class (Naval Rating)
EO2 Engineering Aide Second Class (Naval Rating)

What does E03 mean on hot tub?

AMBIENT AIR TEMPERATURE
E03 ERROR CODE
AMBIENT AIR TEMPERATURE. REASON, THE TEMPERATURE IS TOO LOW. This error code is visible if the ambient air temperature is too low outside. The spa pump will not run if the air temperature is below 4-6°c.

Should I leave my lazy spa on all the time?

Leave Your Lay?Z?Spa Heater Activated Between Uses
Depending on the amount you use your Lay?Z?Spa, in our experience it is better to leave the heater activated all of the time, if used regularly ? say 3 or more times per week.

What does sn mean on a hot tub?

A: Sn error code means there is a problem with temperature sensors in the heaters. They typically mean that the temp sensor or the high limit sensor is shorted or open. In addition, there could be issues with the thermostat or the voltage, which can cause overheating.

What is F3 on hot tub?

Filter Cycles
The filter program also controls how the spa heater operates as follows: • Standard filter programs (F0, F1, F2, F3): Heater activates anytime water temperature drops 2 degrees below the set temperature (Jets 1 low speed also activates on non-Circulation Pump models).

Contents

This entry was posted in Smart Home by Claire Hampton. Bookmark the permalink.
Avatar photo

About Claire Hampton

Claire Hampton is a lover of smart devices. She has an innate curiosity and love for anything that makes life easier and more efficient. Claire is always on the lookout for the latest and greatest in technology, and loves trying out new gadgets and apps.