The bypass feature on your ADT alarm system allows you to choose devices that will not be active when the alarm system is active.For example, if you were to bypass a window sensor, the window could be opened when the system is armed and you’re away, without causing the alarm to activate.
What is force bypass on ADT?
“Forced Bypass”, when enabled, will bypass all open burglary zones, and make the system ready for arming. Once the forced bypass has been performed the system can then be armed.
What does force bypass mean?
Bypass Open Zones The system will bypass open zones while arming the system. This feature can be used to attempt to force the system to arm regardless of zones that may be open. When bypassed, a zone will not trigger an alarm on the system.
What does force bypass mean alarm?
What does bypass mean on alarm systems? To bypass a sensor means to deactivate sensors in one area of your home while leaving the rest of your sensors active. Bypassed sensors are deactivated even while your system is armed.
What does Armed stay bypass mean?
What Is Bypassing A Zone On A Security System? Bypass is the term used to describe the ability to deactivate specific zones of the alarm system before arming the system. Bypassing allows for certain areas to be disarmed while the rest of the space is armed.
How do I know if my ADT system is armed?
At the end of the exit delay, all keypad lights, except the Armed light, turn OFF. LCD5500Z keypads display System Armed in Away Mode and Enter Code to Disarm System. The system is now armed.
How do I bypass ADT alarm zone?
Bypass excludes a zone of protection from the security system until it is un-bypassed or until the next time you disarm the system. Bypassing can only be done while the system is turned off. Press the [Bypass] key followed by your [user code] and then the [zone no.
Arm Disarm Bypass.
| Fast Blink | Alarm |
|---|---|
| Solid On | Not Ready |
What does ADT armed night mean?
Night Arming option is to arm some of the interior motion and deactivate other motion sensors. This is an Arm (Stay) only option. Example: Arm downstairs motion and leave upstairs motion unarmed when you are sleeping at night.
What does bypass away mean?
: to go around or avoid (a place or area) : to avoid or ignore (someone or something) especially to get something done quicker. See the full definition for bypass in the English Language Learners Dictionary.
How do I turn off alarm bypass?
To clear the bypass, if the system is armed, perform a disarm command. This will un-bypass all bypassed zones. If the system is disarmed: select Security > Zones highlight the zones to be un-bypassed and select the “Clear Bypass” button at the bottom of the page. Enter a valid 4 digit user code.
How do I turn off my ADT alarm without the code?
Deactivate Security Alarm Without Code
- Unplug the alarm’s transformer box and remove the battery. The transformer box is likely either in the basement or a closet, plugged into an outlet near your circuit breaker box or fuse box.
- Open up your home’s circuit breaker.
- Flip off the switch and your alarm will shut off.
How do I reset my ADT sensor?
ADT sensors can be reset by restarting the control panel. It may also be necessary to change the batteries in your sensor. Another uncommon option is to reset the sensor to factory defaults by pressing the pairing button on the device’s back for ten seconds.
Does ADT remove equipment after cancellation?
At the termination of your contract, ADT has the right to remove, disable or abandon any of the equipment they own. Typically, they’ll simply leave the equipment on the house, and you (or a new owner, if you sell) can re-activate service at any time.
Why did my ADT alarm go off for no reason?
Check the Battery or Power Supply: ADT alarms typically go off if there is an interruption or breakage in the electrical current of the monitored region. If your alarm goes off unexpectedly, it may be due to an interrupted power supply or battery fault.
How do I stop my ADT alarm from beeping?
An ADT Alarm System’s low battery beeping can be silenced by pressing the OFF button or # button on your keypad. Depending on which version of the alarm system you have, pressing either of these buttons will silence beeping coming from your device.
What is the difference between armed stay and Armed away ADT?
STAY is used to arm the system with people or pets inside the premises. The perimeter sensors will be armed, however interior sensors will be left unarmed. AWAY is used when no one will remain inside the premises. The entire system (interior and perimeter) will be armed and interior movement will trigger an alarm.
What’s the difference between armed stay and Armed away ADT?
Armed Stay is designed for when you plan on arming the system and staying in the home.Armed Away is for when you plan on arming the system and leaving the home. Again, an even wittier name. Arming in the Away Mode will not automatically bypass any sensors, and the entire system, including motion sensors will be armed.
What is quick arm ADT?
Master Code: A master arm/disarm code that can program other user codes.Quick Arm: An option that allows you to turn on (ARM) the security system by pressing either the [ON] or [HOME] key on the code pad control (for ARMING only) as programmed by the installation company.
What is an example of a bypass?
A street designed to let you drive over the highway and skip the highway traffic is an example of a bypass. A surgery performed to create a different path for blood to travel to the heart after your arteries get blocked is an example of a bypass.
What does bypass mean in music?
Bypass refers to allowing a signal to pass through a device without affecting (processing) the signal, i.e., dry. The signal is, however, affected by any input buffers, which can impart a character or slightly degrade the signal.
Where did the word bypass come from?
late 13c., passen (transitive), “to go by (something),” also “to cross over,” from Old French passer “to pass” (11c.), from Vulgar Latin *passare “to step, walk, pass” (source also of Spanish. Intransitive sense of “to go on, to move forward, make one’s way” is attested from c. 1300.
Contents