What is a Flammable Vapor (FV) Sensor? FV Sensors are safety devices on select models of water heaters, which cause a soft lockout (a.k.a. the unit shuts down) when flammable vapors are detected near the unit, to prevent the possibility of their ignition.
What does lockout mean on hot water heater?
The lights on the front show the vacation light on, and A and B, which the manual says is the lockout phase. It gives 4 options: 1) Gas supply is off or too low to operate. 2) Hot surface ignitor not positioned correctly. 3) Low voltage to the water heater.
How does a flammable vapor sensor work?
The carbon, which acts as a conductor, is dispersed throughout the silicone such that, in the absence of gasoline vapor, the carbon particles are in solid electrical contact. When the silicone encounters gasoline vapor, it ex- pands, pulling some of the carbon particles apart, increasing the resistance of the sensor.
Can you bypass a flammable vapor sensor on a water heater?
You cannot easily bypass this sensor.If your gas water heater suddenly stops working, it is very likely that this sensor is the cause.
Are flammable vapor sensors universal?
Answer: Hello, if all the spec. Are the same it will work.
How do you reset the vapor sensor on a Rheem water heater?
Turn the water heater’s gas valve switch to the “OFF” position, wait for a few seconds and then flip the switch to the “ON” position to reset the system.
How do I reset my boiler lockout?
Modern boilers have a reset button on the display button. Once you’ve resolved the underlying issue, simply press and hold the button to reset the boiler after a lockout. For older boilers (or boilers that don’t have a reset button on the front of the boiler) refer to the manual to determine the reset procedure.
A water heater reset button, usually red, is located in the center of the limit switch just above the water heater thermostat. The water heater limit switch is a safety device that will shut the power down to the water heater if something malfunctions and the water gets to hot.
How do you reset an AO Smith power vent water heater?
1 Manual reset is accomplished by first, turning off power to the water heater for 10 seconds. 2 Restore the power to the water heater. 3 Within 10 seconds of restoring power, press the two temperature adjust buttons simultaneously until the left (green) Vacation LED begins to blink (approx. 5 second delay).
How do I know if my water heater is flammable vapor ignition resistant?
A sensor inside the water heater will detect if it has ignited a flammable vapor from outside of the water heater and shut off the flow of gas to the burner and pilot light.
What is a vapor sensor?
The sensor is designed to detect the presence of a specific concentration of gasoline vapors.The proprietary conductive polymer sensing film expands in the presence of flammable vapors significantly changing sensor resistance.
What is flammable vapor?
FLAMMABLE VAPORS ARE A SERIOUS SAFETY HAZARD!
Vapors from flammable productssuch as gasoline, kerosene, paint thinner, and solvents can be ignited accidentally by the pilot light of a propane appliance.Sometimes the vapors may follow air currents in the building to higher levels.
How many ohms should a flammable vapor sensor be?
Rheem SP20172 Flammable Vapor FV Sensor Kit White, 6.7X2. 7X9. 4 inches. Customer reviews.
How do you test a FV sensor?
sensor from it’s bracket on the base ring of the water heater and disconnect both wires to the sensor. Take a resistance reading between the two wiring terminals of the FV sensor and note the resistance value. Service Note: Unless the ohm meter used has an auto-range feature the resistance should be checked twice.
How do you reset a Rheem gas water heater?
Rotate the gas knob on your Rheem water heater clockwise until it is in position. Rotate the water-heater temperature dial counter-clockwise until it is set to the lowest temperature setting. Wait five minutes to let through any gas in the water.
Why does my Rheem water heater keep shutting off?
The power vent water heater keeps shutting off
If your power vent water heater keeps shutting off, the thermocouple could be damaged, dirty or bent. Inspect the thermocouple. If it is damaged, replace it. If dirty, let it down for cooling and then clean.
The high resistance caused by a loose wire produces a substantial amount of heat that can eventually cause fires. If there is a loose electrical connection within your water heater’s system, your reset button’s thermometer can trip (regardless of the water’s temperature) if it picks up the heat from that loose wire.
What causes a furnace to lockout?
All furnaces need to have adequate ventilation and a dirty air filter can cause a system lockout to occur.Another common problem that can cause a furnace lockout is a dirty flame sensor. The flame sensor comes into contact with the flame, and it is quite common for debris to buildup on it.
What is boiler lockout?
A boiler lockout happens when your boiler shuts down due to an issue within the system. Resetting your boiler is usually the first solution for a lockout.
Is a boiler lockout Safe?
an automatic boiler shutdown is a beneficial feature as it prevents the boiler from firing up when there’s an issue within the system. In essence, a boiler lockout helps keep your boiler safe even when something is not working correctly.
Why is my gas hot water heater not heating?
No Hot Water Gas Water Heater. If a gas water heater isn’t heating, a common problem is usually that the pilot light has gone out. This may be caused by the gas valve, the natural gas supply, ormore likelythe thermocouple located next to the pilot light.
Contents