Ecn or Ec Message Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode. The Water Temperature is sampled Only during Programmed Filter Cycles. The Heater will only operate and Heat up to Set Temperature during the Filter Cycles.
What mode should hot tub be on?
We reccommend setting your spa to “Auto” so that the water is always warm and ready for you to use. If you ever notice that your hot tub water temperature has dropped, but there are no error messages displayed on your control panel, you should check that the spa is set to “Auto” mode.
How do you clear a hot tub error code?
Turn your breaker back on without the filters in the spa. Did your error code go away? If it did, it is time to either deep soak your filters (about 48 hours should do the trick) and clean them really well, or, if they are older than 18 months, it is a good idea to replace them.
What is SL mode on hot tub?
SL: Sleep
Sleep mode will only allow the spa to heat within 20 degrees of the set temperature.
What does F8 mean on a hot tub?
Filtration Cycles run from F1 to F8 (F1 = 1 hour every 12 hours / F8 = 8 hours every 12 hours). Preset cycle set from factory is F1, so if in ec or sl mode your water will not reach desired temperature.
What does F2 on a hot tub mean?
The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub.A dirty filter can often be the culprit here so make sure to either replace or give your hot tub filter a good cleaning. Look at your intakes and out takes and make sure they are clear of debris.
AUX input lets you plug in other devices. J-500 Collection, J-400 Collection and J-300 Collection hot tubs have marine-grade speakers plus a subwoofer.
What are the codes on a hot tub?
The Big List of Spa and Hot Tub Error Codes
CODE | ERROR CODE DESCRIPTION |
---|---|
CE 04 | Water sensor/pressure switch fault |
CE 05 | Temperature sensor, or water is dangerously hot |
CE 06 | High limit manual reset on heater is tripped |
CE 07 | Stuck heater relay |
Why do hot tubs have 15 minutes?
Hot tubs have seats at various levels for a reasonto allow you to move around and cool various parts of your body. If you sit at the lowest level for 15 minutes or more, you allow your core body temperature to rise a lot faster than it would if, say, you moved to a seat at which your upper torso was out of the water.
Why does my hot tub keep switching off?
First, check your water level. Then, look for clogs in your circulation system, and wash or change your filter.If the high limit switch shut your heater off because your water got too hot or you have air trapped in your lines, resetting the heater will get it going again.
Should a hot tub be left on all the time?
One question we sometimes get asked is should I leave my hot tub on all the time? The answer is yes! Hot tubs are designed to be left on permanently and this is how they work best. Of course, they’ll need to be drained regularly but for the most part, they are left on 24/7.
Should my hot tub be in ready or rest mode?
*Ready mode is recommended during the winter season to maintain constant warm temperatures and prevent freezing. To save energy but also maintain heat, set the spa to the lowest temperature possible in Ready mode.
What is priming mode on a hot tub?
Once power is initiated to your hot tub it will go through a priming mode. The purpose of the priming mode is to manually activate each spa pump prior to the automatic heat cycle being started. Typically, cycling each pump a few times will prime or purge any air from the plumbing.
What is Dr code on hot tub?
Newer hot tubs have a digital display for error codes that can assist with troubleshooting. A message such as dr or dry or heater dry is a warning that there’s no water in the heater tube, says Niagara Hot Tubs.If the water is low, add water to the proper level and try restarting the pump and heater.
What is F4 code on hot tub?
Codes That Aren’t Errors
Some are simply used to provide you with information on how your hot tub is set to run (known as system status codes).F2, F4, F6 – Displayed by some hot tubs to show how long they are set to filter. F2 = 4 hours, F4 = 8 hours and F6 = 12 hours.
What does Fl mean on hot tub?
Flow
OH = Overheat 108° F, spa is deactivated. Do not enter the water. FL = Flow. Pressure switch is not working.
What does EC mean on a hot tub?
Ecn or Ec Message
Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode. The Water Temperature is sampled Only during Programmed Filter Cycles. The Heater will only operate and Heat up to Set Temperature during the Filter Cycles.
What does blower on hot tub do?
Also called air pumps or bubblers, blowers push air into the spa through small ports or jets. This creates bubbles not unlike those in a glass of champagne. Although water pumps create strong pressure for the best massage, many enjoy the tingling feeling added by a blower.
How do I reset my hot tub control panel?
How to Reset a Spa Heater
- Locate the spa’s high-limit reset. This is a red button found on many spa packs.
- Press the high-limit reset button.
- Turn on your spa and observe its operation.
- Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
How often should you change hot tub water?
every 3 to 4 months
We recommend customers to change their hot tub water every 3 to 4 months. The reason we recommend this is that as your continue to add more chlorine, it will start to dissolve slower and slower until the chlorine doesn’t dissolve in your hot tub anymore.
How long should you stay in a hot tub at 104 degrees?
They should keep their soak times in hot tubs that are 104 degrees F under 5 minutes and in hot tubs between 98-104 degrees F under 15 minutes. Kids should always have an adult with them to keep them safe and to help limit their soak times.
Contents