E. Some thermostats for heat pumps have an E terminal, which toggles emergency heat on or off. Emergency heat should only be used on very cold days when the heat pump is unable to keep the house warm.
Should thermostat be on E or F?
Factory-set in the “F” position, the thermostat fan operation switch is labeled FUEL SWITCH. It’s the correct setting for most systems. The switch should be set to “E” if you have an electric heat system.
What is E on old thermostat?
Some thermostats have an E wire. The E wire controls emergency heating. Emergency heat is used when the HVAC system is not functioning properly (usually when the compressor is out of service). When you set a thermostat to emergency heat, the system bypasses the compressor and directly accesses the electric heat strip.
Should I switch my heat pump to emergency heat?
Short answer: You should only set your heat pump’s thermostat to emergency heat when your heat pump stops heating altogether.Otherwise, just keep your thermostat set on heat. There is no temperature to switch it over to emergency heat, even if your heat pump is running constantly due to cold weather.
What does E heater mean?
Emergency Heat allows your backup heater (gas furnace) to keep you warm until a heating & cooling technician can solve the problem.
Where does the e wire go on a Honeywell thermostat?
The E terminal has a back-up heat source. If you have a heat pump package unit, the E terminal should be wired directly to the heating relay or the stripboard of the air handler.
Where does the e wire go on a Nest thermostat?
1 Answer. The ‘E’ typically goes to what is called ’emergency heat’ which is often the same as and is connected with the ‘AUX’ (auxiliary heat) used with a heat pump system.
What color is E wire on thermostat?
Brown
Thermostat Wiring Color Code Chart
| Marking | Wire Color Code | Description |
|---|---|---|
| E | Brown | Emergency heat relay |
| Y | Yellow | Primary cool call relay |
| Y2 | Yellow | Secondary cool call relay |
| G | Green | Fan relay |
Is W2 and e wire the same?
W2 is generally called on based on a temperature differential between setpoint and space, outdoor temperature, or run time. W3 This is just the next stage of heat after W2. E Is emergency heat, usually just a way to manually drive on what would normally be the secondary form of heat without stage 1 heating.
What is Y1 on a thermostat?
In most systems, the Y or Y1 wire controls your cooling system. If you have a heat pump, your Y or Y1 wire controls your compressor. Your compressor is responsible for heating and cooling your home. The G or G1 wire controls your fan.
What is E heat Mach E?
Dan. No, the Mach E does not have a heat pump, it uses resistive heating (“E-heat” in the Sync Menu). That being said, the benefits of a heat pump are for moderate climates, not very cold ones. So a heat pump is of no value at -40 C. Ford has done a lot of cold weather testing.
What temperature should you set your thermostat in the winter?
68 degrees Fahrenheit
For winter, the ideal thermostat temperature is 68 degrees Fahrenheit when you’re at home. Energy.gov 68 degrees is a good room temperature while you’re awake at home, but recommends lowering it while you’re asleep or away. Lowering your thermostat 10-15 degrees for eight hours can reduce your heating bill by 5-15%.
When should AUX heat come on?
Aux heat should only kick on when the heat pump can’t produce enough heat to warm your home on its own. This is typically caused by one of three factors: when it’s below 35° outside, you’re trying to heat your home by 3° or more, or your heat pump is in defrost mode.
Why is my heat blowing cold air?
Your furnace may be blowing cold air because the filter is too dirty. A dirty air filter blocks airflow over the furnace’s heat exchanger, causing it to overheat. When overheating, your furnace can trip a high limit switch, causing the furnace burners to shut off so that the heat exchanger does not crack.
How do I stop my auxiliary heat from coming on?
Shut the door and close the vents so that the rest of the warm air can be redirected to the rest of your home. If the temperatures are extremely frigid outside, even this may be too much for your unit. You may need to make some additional changes to your home to keep the auxiliary heat from coming on.
At what temperature do heat pumps become ineffective?
Heat pumps do not operate as efficiently when temperatures drop to between 25 and 40 degrees Fahrenheit for most systems. A heat pump works best when the temperature is above 40. Once outdoor temperatures drop to 40 degrees, heat pumps start losing efficiency, and they consume more energy to do their jobs.
What happens if you wire a thermostat wrong?
Potential consequences of improper installation could include: Electric shock. Blowing a circuit breaker. Damaging the thermostat unit, the electrical system or even the AC/furnace unit itself.
Where does orange wire go on thermostat?
The orange wire connects to terminal O on your thermostat. The orange wire only applies to homeowners with an air-source heat pump. Only air-source heat pumps connect to your outdoor condenser. Homeowners with geothermal heat pumps have no use for the orange wire.
What is W2 aux on Nest?
If the heat pump can’t heat the house, the W2/Aux wire will signal the electric elements in the air handler to come on and help out. Those electric elements can also be used as “emergency” heat if the heat pump doesn’t work. I just replaced the same thermostat with new Nest.
What wires call for heat on a thermostat?
The common wire, sometimes referred to as the c-wire, is what’s responsible for delivering constant power to your thermostat. For programmable thermostats and smart thermostats, c-wires are essential for setting a schedule or having your heat or air conditioner turn on at a desired temperature.
What is W2 thermostat?
W2 – This is the thermostat terminal used for second stage heat.Many digital thermostats require 24 volts for power so the common wire is necessary. There is no universal color used for this terminal although black is often used. O or B – These thermostat terminals are for heat pumps.
Contents