Current time of day.
The Big List of Spa and Hot Tub Error Codes
| CODE | ERROR CODE DESCRIPTION |
|---|---|
| CL | Current time of day; system message, not an error |
| COL | Cool – water is 20°F below set point; system message, not an error |
| CoLd | Cold – water is 40°F or less; system should self-start the circulation pump and heater |
https://www.youtube.com/watch?v=Y_u2V_I2IKY
How do I fix the code on my hot tub?
This error message is similar to the FLO error message. Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.
What is FC on hot tub?
The control System checks the water temperature for a reading at or below 60?F(15?C) If an error is detected, the topside control will display the code FC this means a potential freeze condition has been detected (the spa temp is below 60?F(15?C).
What does 1c mean on my hot tub?
When filling* your hot tub in cold conditions a warning message ‘IC’ or ‘ICE‘ may appear. This is to inform you that the water temperature is below 7.2°C (45°F) and open to the risk of freezing.
What is EC mode on hot tub?
Ecn or Ec Message
Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode. The Water Temperature is sampled Only during Programmed Filter Cycles. The Heater will only operate and Heat up to Set Temperature during the Filter Cycles.
What are the codes on a hot tub?
The Big List of Spa and Hot Tub Error Codes
| CODE | ERROR CODE DESCRIPTION |
|---|---|
| CE 04 | Water sensor/pressure switch fault |
| CE 05 | Temperature sensor, or water is dangerously hot |
| CE 06 | High limit manual reset on heater is tripped |
| CE 07 | Stuck heater relay |
What does F8 mean on a hot tub?
Filtration Cycles run from F1 to F8 (F1 = 1 hour every 12 hours / F8 = 8 hours every 12 hours). Preset cycle set from factory is F1, so if in ec or sl mode your water will not reach desired temperature.
What does F2 mean on my hot tub?
The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub.A dirty filter can often be the culprit here so make sure to either replace or give your hot tub filter a good cleaning. Look at your intakes and out takes and make sure they are clear of debris.
What does code SL mean on hot tub?
sleep mode
While your hot tub is in sleep mode (or ‘SL’ & SLP mode on some models), the jets will operate occasionally to filter the water. In sleep mode, your hot tub’s heater will usually only kick on once the temperature dips below 20 degrees of the set temperature.
What is HL code on hot tub?
The HL reading in the display stands for Hi-Limit. The hi-limit is measuring the temperature at the heater, not the actual water temperature of the spa. if your spa is reading HL, it will not allow your heater to turn on and therefore you will notice the pumps will be running close to 24 hours a day.
What does PR mean on Beachcomber hot tub?
priming mode
Beachcomber Hot Tub Error Codes
| Message | Meaning |
|---|---|
| Pr | This happens when the hot tub unit is actuated for the first time; eventually it goes into priming mode |
| F / C | Means unknown temperature. |
| Std/ St STANDARD | Means hot tub unit is functioning in Standard Mode. |
| Ecn/ Ec ECONOMY | Means hot tub unit is functioning in Economy mode. |
What does E1 mean on hot tub?
The E1 Error Code has been implemented to indicate when the Portable Control Unit (PCU) senses a fault with the temperature sensors. This fault may be a worn sensor, corroded connection or wiring.
What mode is best for hot tub?
By default filter modes are 2 hours in the morning and 2 hours in the evening, the rest of the time the hot tub will use the insulation to keep the spa warm and retain heat. Economy is a good setting for those who use the hot tub daily.
What setting should hot tub be on?
The majority of hot tub users prefer a water temperature in the range of 100°F-102°F. 104°F is the standard maximum temperature, which some users also prefer. Always consult a physician before getting in the hot tub while pregnant.
What temperature should I leave my hot tub on?
Your hot tub factory settings will be at 38 degrees, but body temperature of 37 degrees is a generally good start for your hot tub. It’s regarded that women tend to like it slightly hotter at 38 39 degrees.
What is F3 on hot tub?
Filter Cycles
The filter program also controls how the spa heater operates as follows: Standard filter programs (F0, F1, F2, F3): Heater activates anytime water temperature drops 2 degrees below the set temperature (Jets 1 low speed also activates on non-Circulation Pump models).
What is F4 on hot tub?
F2, F4, F6 – Displayed by some hot tubs to show how long they are set to filter. F2 = 4 hours, F4 = 8 hours and F6 = 12 hours. Hold – Displayed when panels buttons have been hit too many times, or too quickly.
Should my hot tub be in ready or rest mode?
*Ready mode is recommended during the winter season to maintain constant warm temperatures and prevent freezing. To save energy but also maintain heat, set the spa to the lowest temperature possible in Ready mode.
What does f1 mean on my hot tub?
FL1 hot tub code indicates that there is an error with the flow switch and it is stuck in the open position.
The High Limit Reset Button is located behind the gas valve.
What does FLC mean on a hot tub?
Now, if you have an FLC, which means it’s reading closed when it’s not running. So, you’re going to go again. Qualify. Make sure the pump is not running and there’s no movement in the tub. There’s nothing flowing through this actual heater and it’s going FLC which means it’s closed.
Contents