On a baitcaster, this can honestly be the hardest part on a baitcaster. If your reel has holes in the spool, you can thread the line through the holes and give the handle a quick twist to get the line all the way around spool. If you don’t have holes, you’ll need to work at it to get the line around it completely.
What is the thing on the side of a baitcaster?
THE DRAG. Usually located on the side near the handle of the reel, the drag is used to set and regulate the tension placed on the line while fighting fish.
What happens if you put too much line on a baitcaster?
If you get too much line on them, you’ll get a weird sound when you cast. Spinning reels should be all the way full, right to the top. If you get too much line on them, the line will jump off the spool in coils. You can stop backlashes with baitcasters by adjusting your reels properly.
Why do I keep getting backlash on my baitcaster?
Backlashes occur when your lure slows down during or after a cast, but the spool keeps spinning, which results in a tangled mess of line. Today’s baitcasters feature sophisticated braking systems and anti-backlash mechanisms that make it easier for anyone to cast without experiencing line overruns.
Do you need backing on a baitcaster?
You can tie monofilament or fluorocarbon directly to the spool and start filling the reel, but braided line slips too much when tied directly to the spool so you will need some type of backing to prevent this slippage.
Is fluorocarbon hard to cast?
While fluoro has some very obvious benefits which keep it on the playing field–extreme clarity, durability, low stretch and a high density that causes it to sink, taking diving lures deeper–it can be very difficult to cast.
What Baitcaster holds the most line?
Round-profile baitcasters
Round-profile baitcasters generally hold more line, making them perfect for big game fish, trolling and angling in the depths.
Does braid backlash more than mono?
The lack of memory is important as it means no rats’ nests and far less likely a chance of backlash (birds’ nests) when casting with a baitcasting rod. Braid is also more expensive than mono. Depending on the brand and quality, it can cost 2-3 times more than monofilament.
Can you cast light lures with a baitcaster?
Typically, 8 to 10-inches from lure to the rod tip works well with a baitcaster. However, when casting a really light lure, you can let out 2 to 2-1/2 feet of line, so that you can get more momentum on your cast, resulting in a great cast distance.
Does braided line backlash?
Braided line is flimsier and folds back on itself more tightly than either mono or fluoro. Pulling on it can make it worse as the line cuts into itself on the spool, making it even more difficult to pick out the backlash. There are also other tools you can use in lieu of tweezers.
Can you put 20lb braid on a baitcaster?
Thin diameter line is great for spinning reels, but if you’re using baitcasting reels, you don’t want to use anything under 20 lb. braid. If the line is really thin, it’ll dig into the spool if you have a big fish on or get snagged, which can cause knots and tangles.
Should you soak braid before spooling?
Braid does not need soaking like you do with mono prior to spooling up. Thread your braid through the eye on the but section of the rod.
Is mono or braid better for Baitcasters?
Mono holds knots better and costs less than braid. It also works better on smaller bait-casting reels because light braid can dig into itself.
How do you put fluorocarbon line on a baitcaster?
When spooling fluorocarbon on a baiticaster, turn the spool up on it’s side and make sure the line feeds from the top of the spool into the reel. Put resistance on the line spool, and wind it on evenly and slowly. Braided line should be tightly wound on the reel. Fluorocarbon needs firm tension but not ultra tight.
How much drag do I need for bass?
Your drag should be set at 25 percent of the breaking strength (pound test) of the line you are using. You can check the breaking strength by tying the line to the scale hook, holding your rod at a 45-degree angle and pulling down on the scale.
How much drag is enough?
Most anglers don’t ever need to go above 25 to 30 pounds of drag, says Rice. “The goal is to tire the fish out,” he adds. “When you get into the higher drags, I’ve seen grown men who didn’t have the right technique in a harness become exhausted quickly.”
How much drag do I need for catfish?
approximately 25 to 35 percent
The drag should slip at approximately 25 to 35 percent of the unknotted line strength for the fishing line. For a thirty-pound test fishing line, this would be 7.5 to 10 pounds.
What’s better mono or fluorocarbon?
Over the long term, fluorocarbon is extremely resistant to the elements as well, unlike monofilament. Overtime, U.V. rays, rain and humidity, and extreme temperatures (both hot and cold) can cause monofilament to break down and lose strength. Fluorocarbon is much more resistant to these conditions over the long term.
Can you use 8lb line on a baitcaster?
That is because the lures I use 8lb and below are easier to throw on spinning gear. I would not hesitate to put 8lb line on a baitcaster.
Can you braid Birdnest?
When you cast the braided line can find itself collecting loops of loose laid line that will be picked up, causing an irregular release and – in layman’s terms – a birds-nest.
What does 150 mean on a baitcaster?
150 is the size and means it’s a right handed reel. 151 would be the same sized reel but left handed. XG is gear ratio or how fast you can reel in with it. Anon. · September 17, 2019.
Contents