For upper-level decks, 2×10 is recommended as the minimum size to use for strong guard post connections. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards.
When should I use 2×6 or 2×8 deck?
That’s a model deck code which includes joist span tables. If there is to be a railing, you need the joists to be at least 2x8s. 2x6s don’t have the depth needed to resist the leverage that can be placed on a railing post bolted to them.
How far can you span a 2×6 for decking?
A decking board made up of 2x6s can span a maximum distance of 24 inches from joist to joist.
How much weight can a 2×6 deck support?
According to the Codes, a 2×6 on edge with the weight pressing through 5.5” of wood will support approximately 53lbs per linear foot. So, an 8-foot length will support about 424lbs. However, a short span 2×6 on edge can support between 600 and 900lbs depending on wood species, grade, and other factors.
Are 2×6 OK for deck joists?
You can use 2×6 as deck joists if the deck is low enough to the ground as not to require guard railing. When using S-P-F 2×6 deck joists, the span must not be greater than 9’0″ (2.73m) with joists at 16″ o.c. (400mm), and 9’10” (3.01m)with spacing at 12″ (300mm).
Can I use 2×6 for joist?
Yes, 2 X 6 lumber can be used for floor joists, but the allowable clear span is only about 4 or 5 feet. Such a small span is seldom useful.
Can I use 4×2 for decking frame?
You have enough posts in. You get the joist spacing by laying a length of your 4×2 between the joists which are bolted to the posts. Each end or these joists will be supported by the perimeter 4x2s. Tight fitting noggins in-between will make it all rigid.
What size joists should I use for decking?
Commonly used joist sizes are 2-by-6, 2-by-8 and 2-by-10. For example, when you space joists 16″ apart — which is standard for residential decks — a deck spanning 9 1/2′ would require 2-by-6 joists, a 13′ deck would need 2-by-8 joists and a 16′ deck calls for 2-by-10 joists.
Can I use 2×4 for deck joists?
The short answer is yes. 2x4s can work for deck joists. However, they aren’t ideal for spanning long distances without bending or breaking, so you have some limitations. Choosing 2x4s for a low-sitting deck is perfect for keeping your feet out of the mud.
Are 2×6 stronger than 2×4?
For example, a 4-foot section of wall would have three 2x4s, but only two 2x6s. The total bearing area of three 2x4s is 15 3/4 square inches; two 2x6s have a bearing area of 16 square inches. In bending, however, such as from a wind load, a 2×6 wall is considerably stronger.
Can a deck hold 5000 lbs?
To determine the maximum load capacity of your deck, start by calculating its total area and multiply by 50 psf. So, a 100 sqft deck would be designed to support 5000 lbs.
How many supports does a deck need?
Before starting to build, the first question is: How many footings do I need for a deck? For an attached 12 x 12′ deck, you’ll need at least 3 footings, plus at least 2 more if you’re planning on building stairs with it. If your deck will be a different size, it’s easy to figure out how many you’ll need.
What size wood should I use to build a deck?
For the deck surface, you can use 2x4s, 2x6s, or 5/4x6s. The 5/4 decking (pronounced “five-quarter”), available in cedar and pressure-treated fir, is 1 inch thick and 5-1/2 inches wide with rounded edges that make for a splinter-free surface. Cedar 1x lumber usually has one rough side and one smooth side.
Can I use 3×2 for decking?
3×2 can be used but you’ll have to support it more frequently throughout its length, say every five feet or so.
Can I use 2×8 for decking?
Q: Can I use 2×8 treated lumber as deck boards? A: No, that’s a not a good idea. Lumber wider than 6 inches should not be used as a flat surface. Wide, flat boards have a tendency to pool rain water, which can lead to cupping problems.
What size timber do I need for a decking frame?
The frame The key to constructing a good decking area is the frame. If the decking is being built on a low level it should be built of C16 graded treated joists 45 mm by 95mm (4×2 approx.). However if you are building a raised deck you should use 45mm x 145mm joists.
How much weight will a 2×6 hold horizontally?
A 2×6 will hold 4 pounds per linear foot horizontally and 53 pounds per linear foot on its edge. Vertically, a 2×6 will hold between 662 and 998 pounds or over 7000 pounds when in a blocked and sheathed wall. However, many factors affect the amount of weight a 2×6 will hold.
How far apart should Supports be for decking?
The short answer: deck joists are typically spaced either 12 inches or 16 inches apart, on center. (On-center means the length from the center of one joist to the center of the next joist, rather than a gap from edge to edge).
How far can a 2×6 decking span without support?
Decking made of 2x4s or 2x6s can span up to 24 inches. If you will run decking at an angle, you might need to put the joists closer together.
Which timber is best for decking?
Hardwood Species
- Ironbark is the most durable hardwood for decking and offers longevity. It is extremely fire, termite and rot resistant.
- Spotted Gum is widely used for decking on account of its durability and strength.
- Yellow and red stringybark are durable enough for outdoor use.
How many joists do I need for a 20 foot deck?
A 20-foot wide deck, for example, would require two beams: one at 10 feet and one and 20 feet in order to support a deck with 2×8 joists spaced 16 inches apart.
Contents