Wind and Motion Somfy’s wired Eolis wind sensor automatically retracts the awning when wind speeds hit any predefined level, from 12mph to 31mph. The sensor checks the wind speed every 12 minutes, and when the winds slow down to a safe level, the sensor will re-extend the awning automatically.
How does wind sensor work on SunSetter awning?
NOTE: The wind sensor is a wireless radio transmitter compatible to work only with SunSetter awnings operated by a remote control. This is a low voltage battery operated device that enables the awning to be closed automatically when it is being shaken up and down by the wind.
How does the Somfy wind sensor work?
Somfy Motors and Somfy wind/motion sensors communicate frequently, and if the wind/motion sensor senses acceleration beyond the threshold it is set at for your application (awning, screen etc.), then the unit will trigger a signal to the motor to close.
Why does my awning keeps retracting?
If the awning automatically retracts every 30 to 60 minutes and and no wind is present, it means the batteries need to be replaced. Please refer to the Changing Batteries on an Eolis 3D WireFree video. The wind sensor needs to be connected to its mounting bracket for it to function properly.
What is wind sensor?
REMS wind sensor measures the wind horizontal and vertical speed as well as the wind direction. The sensor is based on hot film anemometry. These booms are designed to support the wind sensor units in order to reduce aerodynamic effects and minimize weight.
How do you adjust a Somfy wind sensor?
ADJUSTING THE SENSITIVITY OF YOUR SOMFY MOTION SENSOR
- Slide the housing off the base plate in the direction indicated by the arrow.
- Use a small FLAT HEAD screw driver to remove the electronics from the housing.
- Use a small FLAT HEAD screw driver to adjust the sensitivity dial to the desired position.
How do you test a Somfy wind sensor?
Test the sensor by pushing up and down on the awning front bar or arm until it begins to retract. You can use the remote to stop the awning after 5 seconds (first test mode).
What are light sensors made of?
In contrast, photo-junction devices are light sensors or detectors made from silicon semiconductor PN-junctions that are sensitive to light. Photo-junction devices are designed for detector application and light penetration with their spectral response tuned to the wavelength of incident light.
How do you adjust a somfy awning?
Press & hold both the MY/ STOP and DOWN buttons until the awning begins to extend, then release. Stop at the desired lower limit, adjust by pressing the UP or DOWN buttons.
How do you reset a retractable awning?
Press and hold the “Programming” button on the back of the remote a second time until the awning moves back and forth in short movements. The remote control is now reset and ready for normal use.
How do you adjust the tension on a retractable awning?
Adjusting the Awning
Fully unroll the awning and then slide the upper arm into position. While standing in front of the awning, pull the awning tube downward and toward yourself. With your free hand tighten the knob on the upper tensioning arm. Repeat this step with the other tensioning arm.
How do you fix a saggy awning?
It’s easy to fix a sagging awning just crank the handle in reverse until the fabric tightens and be mindful of how the material is rolling. For the best results, make sure the cloth rotates over the top of the roller tube rather than spooling underneath it.
How does a wind gauge work?
An anemometer looks like a weather vane, but instead of measuring which direction the wind is blowing with pointers, it has four cups so that it can more accurately measure wind speed.When wind pushes into the cups, they rotate the axis. The faster the wind, the faster the cups spin the axis.
Which sensor is used to identify the direction of wind?
Wind vanes measure wind direction and are often used with anemometers, which measure wind speed. Campbell Scientific offers a variety of anemometer designs: cup, propeller, ultrasonic, sonic, and lidar.
How does the blowing wind turns the wind blade?
The blades have a special curved shape, similar to the airfoil wings on a plane. When wind blows past a plane’s wings, it moves them upward with a force we call lift; when it blows past a turbine’s blades, it spins them around instead.
How does a light sensor works?
The light sensor is a passive device that converts the light energy into an electrical signal output. Light sensors are more commonly known as Photoelectric Devices or Photo Sensors because they convert light energy (photons) into electronic signal (electrons).The sensor receives the light reflected from the target.
How does a light level sensor work?
Light sensors sometimes use a component called a photodiode to measure illuminance. When beams of light strike a photodiode, they have a tendency to knock electrons loose, causing an electric current to flow. The brighter the light, the stronger the electric current.
How does the detector convert light into current?
Semiconductor-based photodetectors typically have a pn junction that converts light photons into current. The absorbed photons make electronhole pairs in the depletion region. Photodiodes and phototransistors are a few examples of photodetectors.
Contents