https://www.youtube.com/watch?v=vktVxt0AZ28
How do I turn my gas back on with a smart meter?
Press A on the meter keypad to wake up your meter on the wall.
Reconnecting your gas meter
- Safety first. Make sure all your gas appliances are turned off.
- When your gas meter is ready to connect, it’ll say PUSH TO RECONNECT.
- Press any button, and it’ll automatically begin to reconnect (this may take a few minutes).
How do I turn on my smart gas meter?
To activate your gas supply:
- Press any button on your PAYG gas meter to wake it up.
- Press the black button (‘B’) on your meter you’ll see ‘For gas’ appear in the bottom half of the screen.
- Now press and hold the black button until told to release.
How do I wake up my gas smart meter?
Taking readings on your smart meter
To take the reading from your gas meter, you’ll need to press a button to wake up the meter. Depending on your meter, it’ll be either an OK button, a red A button or a round button between two arrowed buttons. The reading will appear on the screen.
How do you turn on the gas on a smart meter?
To re-enable your gas supply:
Press the middle button on your gas meter. Press and hold the middle button. The gas meter will attempt to open the valve. Once the gas appliance check has been completed by the meter, it will display ‘Gas Flow Check Successful’.
How do I turn my gas back on?
The only way to get it turned back on is by you, the homeowner, contacting the gas company. You have to call the gas company and request they turn your service back on. And it’s an almost identical process when a landlord turns off the gas between tenants or a seller turns it off after moving out.
Why is my smart meter not showing gas?
My smart energy monitor has gone blank
Unplug your smart energy monitor. Move it closer to your electricity meter. Plug your smart energy monitor back in. Wait seven days (most smart energy monitors re-start automatically within a week)
How do I reconnect my smart gas meter?
Gas smart Pay As You Go meter
- Press the Black button (button B).
- You will see the message, Appliances Off? Hold A For Gas.
- Press and hold the Orange button (button A) until you see the message, Release A For Gas.
- Take your finger off the button and wait.
- You should see a screen that shows available credit.
How do I turn on my gas supply on my smart meter SSE?
Press and hold the ( OK ) button on the main Prepay screen. Press the ( OK ) button to scroll through the menu until you reach InfoSupply. Then press and hold the ( OK ) button to enter. Press and hold the ( OK ) button to re-enable supply.
Can I turn my gas back on myself?
Once the valve is turned off, do not turn it back on by yourself. It must be turned on by a gas company technician. The gas company will likely perform a pressure test on the system and relight all pilot lights in the house as part of turning the gas back on.
Why is my gas not showing on smart meter?
No Electricity or Gas After Smart Meter Installation
If your electric smart meter is on but the display is blank, try to restart it by pressing B on the keyboard.If your gas supply is off, and you have a gas boiler, you need to double check if all your gas appliances are without gas or just the boiler.
This is your electricity reading. If your meter has an ‘A’ and ‘B’ button, press ‘A’ until you get to TOTAL ACT IMPORT. The number below this is your electricity reading. Your meter might have three buttons to the side of the display.
How do I turn my gas back on on my British Gas smart meter?
Restore my gas supply using my meter
- Ensure that all gas appliances are switched off.
- Press button A on your gas meter to wake the screen.
- Press B on your gas meter.
- Press and hold A until you hear the supply come on.
How do I turn my gas back on after disconnecting?
You are going to need a wrench or gas shut off tool to do this. Very slowly, turn the meter back into the on position. The lever should be in line with the pipe after making a ninety-degree turn. Finally, you can re-light any of the pilot lights in your appliances.
How do I turn on my gas meter?
Before turning on your gas meter, be sure to turn off all gas appliances and pilot lights. To turn on your gas supply, rotate the valve handle into the vertical ‘on’ position. After turning on the gas connection, you should see the gas meter dial move and then stop within fifteen seconds.
Can you turn your gas back on yourself?
NOTE: Once you have shut off the gas at the meter, do not try to turn it back on yourself. If the gas service shutoff valve is closed, PG&E or another qualified professional should perform a safety inspection before the gas service is restored and appliance pilots are relit.
Why does my smart meter only show gas?
If the IHD is only showing gas data it is usually where the IHD has a connection to the gas meter but not the electricity so it is only able to draw one set of readings.
How do you check gas usage on a smart meter?
Smart gas meters
- Press 9 on the keypad.
- VOLUME will appear on your smart meter screen.
- You’ll see 6 digits (e.g. 00123.4) followed by an ‘m3’ symbol at the bottom right of the screen.
- This figure is your latest reading if you’re giving a reading to your energy provider, they only need the first 5 digits.
How do I get my smart meter to work?
Try moving your In-Home Display closer to your electricity smart meter. Once you’re there, turn it off using the round, flat button at the back. Wait a minute and then press the button again to switch the IHD back on. Sometimes, this gives it the boost it needs to get going again.
How do I know if my gas supply is on?
To check and reset it:
- Turn off all gas appliances.
- Turn the service valve off and wait 15 seconds.
- Open the valve one sixth of a turn – you should hear gas flowing through the system.
- When the flow stops, indicating that the gas has fully pressurised the system, slowly open the service valve fully.
How do I get my gas turned back on?
You can use the online Fumigation Start Gas Service form to request the turn on, or call 800-743-5000 (residential) or 800-468-4743 (non-residential). Typical appointment times are in four hour blocks. Note that: The Notice of Re-entry must be posted before PG&E will turn your service back on.
Contents