How to Light a Rheem Water-Heater Pilot
- Rotate the gas knob on your Rheem water-heater clockwise until it is in the “Off” position.
- Rotate the water-heater temperature dial counterclockwise until it is set to the lowest temperature setting.
- Lift the outer door off of your Rheem water-heater.
How do I turn my hot water heater back on?
Turning On a Gas Hot Water Heater
- Step One – Close Open Faucets.
- Step Two – Turn On the Cold Water Supply.
- Step Three – Light the Pilot Light.
- Step Four – Turn the Gas Valve to On.
- Step One – Close Open Faucets.
- Step Two – Turn On the Cold Water Supply.
- Step Three – Remove the Lock Out Safety Tag.
In the center of the limit switch, just above the water heater thermostat, is a normally red reset button for the water heater.
How do you light a gas hot water heater?
Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.
How do you light the pilot on a gas water heater?
How to Light a Water Heater Pilot Light
- Open the door/cover over the pilot light access.
- Use a flashlight or a headlamp to find the burner inside.
- Turn the gas knob to Pilot, press and hold it down.
- While still holding the gas down, light that pilot.
How do I turn on my electric water heater?
For an electric water heater, you’ll need to locate the circuit breaker that controls the heater and turn it on. If the breaker isn’t labeled, look for a double-pole breaker that has the same amp rating as the heater. Simply switch on the breaker to turn on the electric water heater.
Where is the pilot light on my water heater?
The pilot light on most water heaters is located at the base of the unit, below the gas control valve. Open the access panel or door to the burner chamber and look inside. There, you’ll find the pilot light tube, which should have a steady blue flame. If you don’t see the flame, the pilot light is out.
How do I reset my Rheem?
How to Restart a Rheem Air Conditioner After Power Loss With the Reset Button
- Raise the temperature on your thermostat to 80-degrees Fahrenheit.
- Find the red rubber boot that covers the rest button on the back of the air conditioner case.
- Press the reset button once with your finger.
Why is my hot water heater not getting hot?
If an electric water heater is not producing hot water, it could be a simple problem like a blown fuse or tripped circuit breaker. Additionally, some electric water heaters have a circuit-style safety switch located near or on the thermostat.
How do I turn on my gas heater in my house?
How to Turn On a Wall Heater
- To turn on your gas heater, locate the knob for starting.
- Turn the knob to “Pilot,” and then push down on the “Ignite” button.
- Once the pilot light comes on, hold down the Ignite button for 10 to 15 seconds.
- Set the temperature on the wall heater to your desired heating level.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How do you turn on a pilot light?
Turn the gas regulator valve to the pilot position. If the water heater has a manual ignite button, press that to light the pilot. If it doesn’t have the button, or the button fails, press the regulator valve and hold a grill lighter or long match to the pilot light valve until the pilot ignites.
How do you tell which water heater is hot and cold?
Remove the cap and have someone watch while you turn on the cold supply. IF water comes out it is a cold pipe. If not, leave the cold on and then open the heater valve. If no water comes out then, it is a dead line.
Contents