How far behind the boat should I troll?
Every boat is different and you should make your boat your own study. Proper distance for most boats will be anywhere from 20 feet to 150 feet behind your boat. Whether you have inboard diesel or outboard gas engines, your power dictates the distance you troll your baits and lures.
Should you troll with or against the current?
When in an area with current, troll crosscurrent as opposed to with and/or against the current. Going crosscurrent, you don’t have to worry about how the current is affecting your lure’s or bait’s speed through the water. Plus, fish generally swim into the current.
How fast should you troll for striper?
Slow Trolling Speed: The slower you go, the deep your lures will drop. I deal striper trolling speed is as low as you can go, preferably under 3.5 kts through the water. Don’t worry about speed over ground while trolling with the tide.
How deep do you troll for striped bass?
Light: Also sunrise and sunset hours are ideal for stripers. Also, as importantly, boat traffic is at a minimum during these times. Depth: Your focus is on bottom dwelling fish. Have gear for the depths you’ll be fishing, say 10′ to 50′.
What is the best rig for striped bass?
Striped Bass Rigs
When using cut bait for striped bass, one of the most popular rigs is the fish finder rig. This rig can be found in the surf fishing kit attached with a circle hook between size 1/0 and 5/0. This rig is best used with 2-4 inch chunks of cut bait such as bunker, herring and mackerel.
What is the best rig for flounder?
Best Flounder Rigs
Like the basic fish-finder, this flounder fishing rig begins with the fishing line running through an egg, bullet or flat sinker, which is then tied to a barrel swivel. Next, a two-foot section of mono that’s lighter than the main line is tied to the opposite end of the barrel swivel.
What is a donkey rig?
Essentially, the Donkey Rig is a dual-fluke setup used to imitate multiple shad on the run. It is made up of two leaders, two hooks and a pair swivels.
How fast do you troll with a Rapala?
Troll worm harnesses behind bottom bouncers or floating Rapalas on a three way rig as slow as 0.8 mph. These same tactics work on lethargic post spawn walleye as well. Trolling really kicks into high gear for summer walleye. Start trolling at speeds of 2.0 mph and adjust as necessary to encourage strikes.
What is the best line for trolling?
Monofilament
Monofilament is the best line choice for trolling in most situations, but there are times when low stretch lines have the edge. Because low stretch lines are super thin, they enable trolling lures like crankbaits to pick up significantly more depth compared to monofilament lines of the same break strength.
How do you control crankbait depth?
Move your crankbait too slow or too fast and it’ll run too shallow. The bill has to bite into the water at the correct angle for the lure to run as deep as possible. The length of your cast is the next thing that affects running depth. A longer cast will let the bait get down deeper.
How much line should I put out for a troll?
Trolling Depth Trick #3
Consider the following example: If you’re trolling a tandem rig tied with two five-ounce bucktails (5 x 2 = 10), and you let out 100 feet of line (double 50, so multiply by two again), according to the Rule it will run at about 20 feet below the surface (5 x 2 = 10 x 2 = 20).
How do you slow down a boat while trolling?
Shut Down Your Boat’s Engine(s)
With triple outboards, for example, shutting down the center engine (or leaving it in neutral) will help you troll slower. If that’s not slow enough, use just the center outboard and turn off the two outside motors. With quad outboards, try running just two motors.
What makes a good trolling lure?
Topwater plugs often produce better results in warmer weather/water while diving lures produce better results in cooler weather/water. Color and action also play a factor in the results you will get when using bass trolling lures. Keep in mind, the bass has some of the best eyesight of any fish.
How do you troll live eels for striped bass?
Cut the mono and tie a stinger hook to the end of the mono exiting the eel’s anus. Cut the mono down and tie the other end to the bend in a live bait hook. Hook the live bait hook through the eel’s head. The finished eel should be hooked through the head by the live bait hook.
Contents