How Do You Troll In A River?

Do you troll up a river or down?

As mentioned earlier, trolling up stream can help you slow your boat, and the baits get much more action being as they are working agsinst the flow. Going down stream you’ll, at times, have to go much faster to get the proper bait action and they can do some strange things in higher flow/current.

Do you troll upstream or downstream?

For all those reasons, trolling downstream is the best way to get at them. First off, by going downhill, you can crank up the trolling speed — which allows you to cover the water (and find fish) more quickly.

How fast should I troll?

So, what is the best trolling speed? The best trolling speed depends on several factors including the type of fish, water conditions and lure choice. In general, trolling speeds between 1.5 and 2.5 mph, as measured by GPS, are a good starting place for most species like walleye, trout and salmon.

Should you troll into the current?

Just remember, if you go with the current, you will have to troll faster than the current to achieve the best action for your lure. 85% of the time I troll against the current. It gives you more control working the breaks, and better bait action.

How fast do you pull crankbaits?

Determine a depth – Like Whitehead, using 90 to 110 feet of line is a good starting point. At 1.5 mph this will put the 8- to 12-foot crankbaits between 12-16 feet, depending on wind on waves. Choose a speed – 1.5 to 1.7 mph is where Whitehead stays and is a common speed for pulling cranks.

How far behind the boat should I troll?

Every boat is different and you should make your boat your own study. Proper distance for most boats will be anywhere from 20 feet to 150 feet behind your boat. Whether you have inboard diesel or outboard gas engines, your power dictates the distance you troll your baits and lures.

How do you properly troll?

Consider this a “beginners guide” to trolling – so if you want to learn how to troll, or troll more effectively, read on.

1. Get The Right Gear.
2. Have A Plan.
3. Use Your Electronics.
4. Start Small, Work Bigger.
5. Don’t Stop.
6. Try Multiple Presentations.
7. Change Speeds.

How much line should you let out when trolling?

Downriggers. Downriggers allow for extra long length between the downrigger ball and the lure. Let out 50 feet of line and clip into the release. If that’s not enough distance to prevent your lake’s wary walleyes from seeing the ball…then let out 150 feet of line!

Can you troll in a river?

The most important rule in river trolling is to motor upstream very slowly so the current will keep the plug working. When you turn and troll downstream, you’ll have to go considerably faster than the current to get any action out of a plug.

Can you troll kwikfish?

When trolling or backtrolling in water less than 10 feet deep, the standard Kwikfish can be fished without any additional weight.Slow current or a short trolling distance (30 feet) produces a shallow dive, while strong current or a long trolling distance (50 feet) will produce a deeper dive.

How do you troll with a spoon?

A spoon should wobble from side-to-side and will produce its best all-around, fish-catching action when trolled at speeds between the slowest that produces a wobble and the fastest darting action that does not cause the lure to revolve or spin. For fast trolling try the Krocodile.

How do you fish in strong current?

How To Catch Fish In Heavy Current

1. Use heavier lures or weights to get your bait or lure down to the bottom.
2. Use pyramid sinkers if using live bait (egg sinkers roll and move too fast along the bottom)
3. Cast farther up current so that your bait or lure has enough time to get to the bottom.

How do you troll in the ocean?

In a nutshell, trolling is a fishing technique that employs dragging a hooked lure or bait through the water from a moving boat. You can have any number of lines in the water, but the principle is the same – you’re supposed to trick the fish to think that your bait is moving prey.

How deep do you troll for walleye?

Depth. Crankbaits are an effective way to fish both in shallow areas and at depth. Deep running crankbaits for walleye go down to 12 feet or deeper. Smaller bills and shallow divers cover depths of zero to eight feet deep.

Can you troll a jerkbait?

Trolling shines whenever fish relate to large, mostly featureless locations and spread out over broad areas. It’s also is good whenever you are in search mode, covering a new area quickly. Trolling jerkbaits can also rule when fish are 5 to 10 feet deep and won’t rise to a bait.

Can you troll with a crankbait?

Trolling with crankbaits is a good time. In this link, walleye expert, Dale Gilbert, explains his setup and a technique that he uses to make sure lures are tuned.

How do you control crankbait depth?

Move your crankbait too slow or too fast and it’ll run too shallow. The bill has to bite into the water at the correct angle for the lure to run as deep as possible. The length of your cast is the next thing that affects running depth. A longer cast will let the bait get down deeper.

How do you deal with trolls?

5 tips for dealing with trolls

1. Starve them. It’s totally understandable to want to wage a war on trolls with your keyboard, but trolls thrive on others’ anger, frustration and annoyance.
2. Record it. Take a screenshot so that you have a record of the original post.
3. Stand up for yourself.
4. Log off.
5. Tell someone you trust.

How fast do you troll for striper?

According to the Fishaholics, when fish are less active, the ideal speed is about 2.0 to 2.5 mph. When the fish does not bite, or the bite is tough, it is better to go below to 2.0 mph. However, if striped basses are active, you can opt for a higher speed between 2.5 and 3.5 mph.

Can you catch walleye on rooster tails?

So tell me what your favorite lure and color is. I don’t particularly like to fish species specific but the inline spinners (rooster tail specifically) have been treating me pretty well for walleye and I also really enjoy using a roadrunner jig head with gulp minnows.