How Can I Restart My Pilot Light?
- Step 1: Turn off your furnace.
- Step 2: Locate your gas valve.
- Step 3: Hold down the red button.
- Step 4: Light the pilot light.
- Step 5: Let go of the button.
- Step 6: Turn your gas back on.
- Step 7: Turn your furnace back on.
How do you reset the pilot light?
Relight the pilot light.
Turn the knob to Pilot, and let gas to flow to the pilot. Light a lighter or match, then push in the reset button. Hold your flame to the pilot light’s opening. Keep the reset switch depressed until the pilot light is burning steadily.
Why is my furnace turning on but not igniting?
The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up.If the sensor or ignitor is dirty, it will need to be cleaned.
What do you do if your pilot light won’t turn on?
How to Fix Your Pilot Light
- Find your gas valve.
- You need to turn the valve to the off position for at least three minutes.
- Once you have had the valve at off for a few minutes, switch it over to pilot setting.
- You will need a match that is lit.
- Set the pilot valve to the on position.
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
What can cause a pilot light to go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
How can you tell if a furnace ignitor is bad?
4 Signs of a Faulty Furnace Ignitor
- The Furnace Stops Running. When a furnace won’t run at all, check for a bad ignitor.
- Your Furnace Blows Chilly Air. Unless you’ve set your thermostat to COOL, your furnace should not blow cold air.
- Does Your Furnace Short Cycle?
- A No Glow Ignitor.
- We Can Replace Your Furnace Ignitor.
Should the pilot light always be on in a gas furnace?
Most furnaces with electronic ignition have a device called a hot surface igniter.The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.
Where is my furnace ignitor?
Unscrew and remove the service panel on the side of the furnace and find the ignitor. It is usually mounted on a V-shaped bracket near the gas port. The ignitor has two wires attached to the back of it and has a flat metal tip.
Will a furnace turn on if pilot light is out?
The pilot light, however, is an actual old-fashioned flame inside your furnace. This flame is supplied by your gas line and should always be lit.If it goes out, the safety features of your furnace will not allow it to release gas into the burner, meaning that the furnace will not run at all.
Is it hard to light a pilot light?
It’s not difficult to relight your gas furnace’s pilot light. As with these other appliances, it’s best to check with the manual first, but you can expect the process to be about as simple as it appears here.
How do I get my furnace out of lockout mode?
Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.
How do I get my furnace to kick on?
What would cause my furnace not to kick on?
- Check your circuit breakers.
- Check your thermostat settings.
- Ensure your furnace filters are clean.
- Check your pilot light.
- Check your blower motor.
- Check the furnace ignition switch.
Why is my furnace not blowing air?
Your filter could be so saturated with dust and debris.Every modern furnace is equipped with a safety shutoff that will be tripped if your furnace gets too hot, and a clogged air filter can cause your furnace to overheat, shut itself off and give you the illusion of a furnace not blowing air.
How long does furnace ignitor last?
about seven years
Fortunately, you can replace the ignitor without replacing the full furnace. Most ignitors last about seven years. Keep reading to learn how you can tell if your furnace problem is a faulty ignitor.
Can a furnace ignitor be cleaned?
Try Cleaning the Ignitor With Compressed Air
If your furnace has a spark ignitor and it’s working haphazardly, it too could be covered with soot, and a blast of compressed air may be enough to clean it. Compressed air can also clean a blocked pilot tube that is causing the pilot flame to burn weakly or not at all.
How much does it cost to fix a furnace ignitor?
Here’s the bottom line: Whether for a natural gas furnace, oil, or a propane furnace, replacing a furnace ignitorincluding parts and laborwill cost you around $300 $425 for a qualified contractor to install. Compare that to, say, a draft inducer motor, which will cost $400 $1,500 to replace.
What would cause a pilot light to not stay lit?
The Buildup of Dirt or Debris Around The Pilot Light Over the years it’s easy for dust, debris, and dirt to build up on the inside of the intake valve where the pilot light resides. This makes it difficult for the flame to breath and as a result causes the pilot light to go out suddenly.
Will gas leak if pilot light is off?
If the pilot light goes out on a storage or instantaneous hot water heater, space heater or a ducted heater, you will not have a gas leak. This is because all modern gas appliances with pilot lights have a fail-safe device that closes off the gas to the appliance in the case when the pilot may go out.
Are furnace ignitors interchangeable?
Most ignitors are interchangeable as long as they fit in the furnace space provided. Select your ignitor by looking at the one you have, and comparing it to the photos of ignitors here; select the one most similar.
Can you manually light a gas furnace with electronic ignition?
If your furnace is equipped with an electronic igniter, you cannot light the furnace manually. However, you may be able to get the furnace working by turning off the igniter and resetting it. Find the paperwork for your particular furnace to locate the reset button or switch.
Contents