How Do You Reset Hunter X2?

X2

  1. Press and hold down the , and buttons.
  2. Press and release the RESET button on the right side of the controller.
  3. When ‘DONE’ appears on the LCD, release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.

How do I reset my hunter X2 irrigation controller?

X2 – Total Reset

  1. Turn the dial to the RUN position.
  2. Press and hold the program button.
  3. Press and release the RESET button located inside the lower wiring compartment.
  4. When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.

How do I reset my hunter water system?

Resetting a Hunter X-Core is easy. To reset the irrigation controller, all you need to do is press the negative, the hand and the program keys at the same time, then use a small tool to press in the small reset button on the side of your controller. A small screwdriver or a pen will do the trick.

How do I reset my hunters wand?

WAND – Factory Reset

  1. Press and hold the WAND button for 5 seconds and Fdr will appear on the controller LCD.
  2. The module LED will turn off.
  3. Release the button when the solid amber. LED appears.
  4. Return to the online setup wizard in your Hydrawise controller settings account page to reconnect WAND to Wi-Fi.

Why does my irrigation system finish watering and then start again?

A common reason why a program is repeating is that you have a second start time set. The start times control the exact time your ESP-Me timer will begin to water and they also control how many times a day your timer will water. The ESP-Me allows you to set up to 6 start times per program.

See also  How Do I Register My Smart Account?

How do I reset my core controller Hunter?

  1. Turn the dial to the advanced features position. Press the down arrow to scroll to page two. Select ERASE ALL by pressing the “+” button.
  2. Press and hold the “+” button. The display will briefly inform you to please wait and then indicate when the reset is done. 2.666665.

How do you bypass a hunter rain sensor?

Simply turn the dial to RUN (BYPASS SENSOR) and the weather sensor will be overridden. The wireless rain sensor may be bypassed by using the built-in bypass feature on the receiver. To bypass the sensor, press the SENSOR BYPASS button on the receiver. The bypass status light will turn red when the sensor is bypassed.

Is there an app for Hunter sprinkler system?

Hunter Hydrawise
Remote access is possible through either the Hydrawise app (iOS or Android compatible devices) or online through their cloud software. Key product features include: Predictive Watering Adjustments based on web-based weather data brings up to 50 percent in water savings.

Does the hunter X2 have a battery?

The X2 controller has a non-replaceable 3V CR2032 lithium battery installed directly on the circuit board. The controller will immediately enter hibernation mode when AC power is unavailable.

Why do my hunter sprinklers turn on twice?

A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time. NOTE: In the Start Times dial position, the numbers 1-4 do not represent stations.

See also  Is Applecare The Same As Limited Warranty?

Why isn’t my hunter sprinkler system working?

If your controller shows irrigation running (Flashing Sprinkler Icon), and your sprinklers are not working, you may have a wiring problem at the valves or the irrigation water supply has been shut down.Check the wiring connections at the master valves for loose or corroded connections, or a bad solenoid.

Why is my controller not starting the watering cycle?

Go to one of the irrigation valves and turn the solenoid 1/4 to 1/2 a turn counter-clockwise.If the valve opens and sprinklers turn on, your valve is working and you’ll need to check the controller and field wiring. If the valve did not turn on any of the sprinklers, the water to the valves is still off.

What does bypass mean on Hunter sprinkler system?

Toggle switch that controls the input signal from the weather sensor (Rain-Clik, Freeze-Clik, Wind-Clik, etc). When the switch is set to “Bypass” the controller will ignore the signal from the sensor and irrigate normally.

How do you test a hunter rain sensor?

If you want an immediate synchronization, press and hold down the “Test” button for 5 seconds, then release the “Test” button. The “Sensor Status” LED will turn to green. You can manually test proper operation of the rain sensor by using the One Touch Manual Start.

How do you adjust Hunter rain sensors?

The Mini Clik uses a spindle adjustment to set the amount of rain you want the sensor to witness before it shuts down the system. This amount can be set by adjusting the spindle on top of the sensor and the range is 1/8″ (3.17mm) to 1″ (25.4mm).

See also  Can I Make Your Nickname Alexa?

What is SAP mode WiFi?

Wi-Fi Direct Setup (SAP mode) uses the Wi-Fi feature on your smartphone, tablet, or computer to connect your controller to Wi-Fi. Navigate to the Hydrawise setup wizard on the Hydrawise app or Hydrawise.com website.

How do you connect a controller to the Internet?

From Home screen touch Settings button then the Wireless button. Select your wireless network from the list shown on the controller display and press the Confirm button on screen. Enter your wireless password and press the OK button on keyboard.

Contents

This entry was posted in Smart Home by Ruben Horton. Bookmark the permalink.
Avatar photo

About Ruben Horton

Ruben Horton is a lover of smart devices. He always has the latest and greatest technology, and he loves to try out new gadgets. Whether it's a new phone or a new piece of software, Ruben is always on the forefront of the latest trends. He loves to stay up-to-date on the latest news and developments in the tech world, and he's always looking for ways to improve his own knowledge and skills.