Resetting your Ring Smart Lightbulb
- Using a power switch, turn the bulb off.
- Turn the bulb on and off six times. Each on cycle should last two seconds and each off cycle should last two seconds – for a total of four seconds.
- Wait about 30 seconds.
- At this point, your Ring should now be back to factory settings.
Why is my ring light not working?
Check your batteries. Check the area around the lights. There may be something in the area (like a small animal) that is triggering your lights. Check your motion sensitivity controls in the Ring app.
Why is my Ring floodlight lights not working?
If the light on your Floodlight Cam does not light up and flash and your Floodlight Cam is wired correctly and is receiving power, you can try performing a hard reset. Hold down the top button for a full 30 seconds.
1 Factory Reset a Spotlight/Floodlight Cam
- Make sure the camera is powered up.
- Press and hold the reset button atop the camera for 30 seconds.
- After releasing it, the status light located at the bottom will flash a few times indicating the camera is restarting.
- The camera is now reset to factory defaults.
How do I reconnect my ring light?
Holding the button down for six to 10 seconds: This is a power cycle/reset – This will cause the device to forget any of the settings previously saved and will force you re-set up all the lights.
How do I reset my outdoor motion sensor Ring?
Factory Reset your Motion Detector:
- Remove the Motion Detector back cover. Keep the batteries in the device.
- Use the pinhole tool or a paper clip to press and hold the reset button (on the back of the device) until you see the LED on the front turn red, about 10 seconds.
How do I get my Ring sensor back online?
Remove the cover from the device, and remove the battery. Wait a few seconds and then reinsert the battery. — If you get a very quick LED flash, the Contact Sensor is in-network. — If you get 3 blinks, the Contact Sensor is out of network.
Why Does My Ring light stay on?
Adjust them to what’ll suit your requirements, and hit Save. Then between those times, your Ring Floodlight Cam’s two lights will permanently be on. If motion is detected in this time, they’ll stay on even after the automatic shut-off timer has expired.
Why is my Ring blinking?
Usually, when your Ring Doorbell is setting up, the light will spin and not flash. The LED light will change to a flashing blue pattern that moves upwards to indicate that your doorbell is in the process of connecting to your Wi-Fi network.
How do I factory reset my indoor Ring camera?
Resetting a Ring Stick Up Cam to its factory default state will erase all its saved settings and preferences.
- Make sure the camera is powered up or the battery is charged.
- Press and hold the reset button on the back of the camera for 15 seconds.
- Release the button.
- The camera is now reset to factory defaults.
Why is my Ring floodlight flashing blue?
Flashing blue means your Spotlight Cam may be too far from your router to get a decent signal. You may need to get a Ring Chime Pro to boost the Wi-Fi signal to your Spotlight Cam.
Ring Stick Up Cam Battery (2nd Generation)
- Undo the battery cover.
- Find the orange setup button near the battery slot.
- Press and hold the setup button for 10 seconds.
- The light on the front of the camera will flash for several minutes; when the light turns off the reset is complete.
Why are my ring lights offline?
Losing power is by far the most common cause of network disconnection. This includes power surges and issues with the power connections. To check whether your Floodlight Cam has lost its power: If the Floodlight Cam is connected to a light switch, check to see if the light switch was flipped off accidentally.
How do I reset my ring sensor?
How to factory reset your Contact Sensor (2nd generation)?
- Remove the cover from the device.
- Press and hold the pinhole reset button using a paperclip or the included pinhole tool.
- Continue holding down the pinhole reset button until the LED light turns red.
- Put the back cover back on the device.
The device’s red LED turns on solid to indicate the device was removed from the network. 1. To restore Ring Alarm Contact Sensor to factory default settings, locate the pinhole reset button on the device. This is found inside the battery compartment on the back of the device after removing the back bracket.
How do you clear a tamper on a ring sensor?
A tamper status means there is a physical disconnect on the inside of the sensor. This is usually caused by the casing of the Motion Sensor not being fully secure. If the Motion Sensor casing is opened, close the sensor and the Tamper message will clear afterwards.
How do you reset a ring motion sensor?
Factory Reset your Motion Detector:
Press and hold the reset button under the pinhole found on the back of the device. A paperclip works well. The LED on the front of the sensor should begin blinking. Hold the button down until the LED stops blinking.
How do I turn off the light on my ring doorbell?
The Steps
- Open the Ring App.
- Click the Main Menu in the Top Left Corner.
- Click Devices.
- Click On Your Ring Chime Pro.
- Click the Nightlight Toggle to Turn Off The toggle is the little blue dot on a blue line which when clicked, slides from one side to the other.
Can you turn off the blue light on ring camera?
So far, there doesn’t appear to be a way to disable the blue LED lights on the front of ring cameras.You will have to turn off the light in the app and also go to light settings and turn off each light motion zone. Otherwise the motion dectector will keep turning the light back on.
Can you tell if someone is watching you on ring?
There isn’t any way to know if someone is watching you on a Ring cameraat least not through physical observation. However, it’s possible you could see the infrared light at night turn on if the camera is activeassuming the night vision is on and you’re at the correct angle to view it.
What does the blue light on ring mean?
The light on the Ring Doorbell will spin blue when it is notifying you of a potential call.This indicates the doorbell speaker is turned on and someone has connected and can listen. Upward Moving Blue Light When you see an upward moving blue light then your Ring Doorbell is trying to connect to your WiFi network.
Contents