In the event of a fault, the blue mains indicator light will flash if there is a fault. To reset the boiler turn the Central heating temperature knob anticlockwise to the RESET position and hold for approximately five seconds and then turn the knob back to the original temperature setting.
https://www.youtube.com/watch?v=w5N4CKbn4kM
Why is my Worcester boiler not firing up?
If the boiler is not igniting, there is a possibility the valve is blocked, seized or there is damage in the wired connections. No Pilot Light: When the boiler is not igniting and the pilot light has gone out, this usually means debris has blocked the jet.
Does a Worcester combi boiler have a pilot light?
I’m sorry to hear of the problems you are encountering with your Worcester Greenstar condensing boiler. We are a little confused with your comments though as the Greenstar doesn’t have a pilot light, the boiler has a fully automatic ignition system.
How do I reset my Worcestershire boiler?
Tell Me How to Reset a Worcester Boiler
When you need to reset your boiler, simply press and hold the reset button that can be found on the front of your boiler control panel. You need to hold the button down for 3-5 seconds to ensure that it is reset before re-checking the system to make sure it is working.
How do you reignite a pilot light?
Relight the pilot light.
Turn the knob to Pilot, and let gas to flow to the pilot. Light a lighter or match, then push in the reset button. Hold your flame to the pilot light’s opening. Keep the reset switch depressed until the pilot light is burning steadily.
How can I reignite my boiler?
How do you relight the pilot light on a boiler?
- Turn the gas to ‘pilot. ‘
- Press and hold the reset switch for one minute and hold a flame to the pilot light at the same time.
- If all is working as expected, return any casing/doors and turn the gas from ‘pilot’ to ‘on.
How do you reset a Worcester Bosch boiler?
To reset the boiler turn the Central heating temperature knob anticlockwise to the RESET position and hold for approximately five seconds and then turn the knob back to the original temperature setting.
How do you fix a boiler that won’t ignite?
If you still can’t light your boiler, there could be debris blocking the jet. Boiler pilot light jets are relatively cheap to replace but can also be removed, cleaned and re-installed. Your heating engineer will be able to advise you on the best course of action and replace the jet accordingly.
Should Worcester boiler have flame light?
The green light on a Worcester Bosch boiler typically indicates that the burner is operating properly, which is a good sign. However, sometimes the green light can go off, with the boiler still working fine.
How do you reset a Bosch boiler?
In most cases, you will simply need to hold the button marked ‘reset’ for three seconds. In some models you may see a reset light at the end of the temperature dial. In this case, just turn the dial down to the reset light, leave it there for three seconds and then turn it back to its original position.
How do I reset my Worcester 28cdi boiler?
The appliance can be reset by pressing the reset button and holding in for 5 seconds. Check that the gas supply has not been interrupted. If this condition continues to occur, then call a service engineer.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
How do you reignite a gas hot water heater?
While holding the gas switch down or the button, light the pilot. Depending on the model, your water heater may have an igniting button, or you might need to light it manually with a long lighter. Once the pilot light ignites, be sure to continue holding the switch or button for a full minute.
How do you reset a Worcester Greenstar boiler?
Turn the Central heating temperature knob anticlockwise to the RESET position and hold for approximately five seconds and then turn the knob back to the original temperature setting. Wait two to three minutes for the boiler to restart.
Usually, when modern boilers need resetting they will display a fault code or begin to flash a red or green light. These signals indicate that your boiler senses a problem, which is why it has stopped working and needs to be reset.
Can you manually ignite a boiler?
Manual Boiler Pilot Light Ignition
The knob will be situated on top. If you smell any gas, allow the smell to dissipate for 15 minutes.Turn the gas control knob to the “pilot” position, then press down on the knob. Pressing down on the knob will release gas into the pilot light orifice.
Why has the pilot light gone out on my boiler?
If the pilot light on your boiler has gone out, the cause is usually debris blocking the jet.Even a small spec of dirt can block it, cause the pilot light to go out, and then the boiler won’t re-ignite. These jets are cheap to replace, but they can usually be removed, cleaned and reinstalled to fix the problem.
How do I reset my wireless thermostat?
A common way to reset almost any thermostat is to hold down the reset button for 5+ seconds. Alternatively, try resetting battery-powered thermostats by flipping the battery directions around for 5s, then flip them back. If all else fails, switch off the power at the circuit breaker for a couple minutes.
How do I reset my Worcester Digistat thermostat?
If at any time during the programming you get confused and would like to start the procedure from the beginning press the SELECT and buttons at the same time and hold for two seconds. This resets the Digistat to the factory pre-set times and temperatures (Table 1).
Contents