How Do You Read A Landis Gyr Smart Gas Meter?

If your gas meter serial number starts with E6S it will be a Landis + Gyr Meter If it is a Landis + Gyr meter, to get your meter reading you need to hold button A until you see ‘Please Wait’ then let go. Press button A to cycle through screen until you see the meter index screen which will have the reading on it.

How do you read Landis Gyr?

How to REALLY read my Landis+Gyr electricity meter

1. Press button A for two seconds: screen with garbage displayed.
2. Try it again: press button A again for two seconds.
3. Press button A again.
4. Press button A again.
5. Press…
6. eventually the screen will show a display: not kWh, but ‘Credit Mode Bal’

What is the B button for on my gas meter?

This is your electricity reading. If your meter has an ‘A’ and ‘B’ button, press ‘A’ until you get to TOTAL ACT IMPORT. The number below this is your electricity reading. Your meter might have three buttons to the side of the display.

How do I find my Landis Gyr meter number?

Enter a unique code to find your prepaid electricity meter number

1. If you have a Hexing meter – Press 804.
2. If you have a Landis+Gyr meter – Press i000 (i is the information button below the number 9)
3. If you have a Conlog meter – Press #100#
4. If you have a Wasion meter – Press 75 Enter.

What is a Landis Gyr E470?

In addition to ably performing all the functions one would expect of a single phase smart meter, the Landis+Gyr E470 uses SMS messaging rather than GSM which therefore allows token-less prepayment as well as remote meter reading and programming.

How do I reset my Landis Gyr meter?

Turn off all appliances. Press any button on the meter to reset the meter. Turn on only the appliances that you need. If you do not reduce the number of appliances being used, the meter will trip a second time.

How do you read a smart gas meter with A and B button?

If your meter has A and B buttons under the screen

1. press the A button.
2. press the A button again until you see ‘METER INDEX’ and numbers followed by ‘M3’
3. write down the number from left to right.
4. ignore any zeroes at the beginning and any numbers after the decimal point.

How do you read a smart gas meter?

Reading your Gas Meter
The four small dials at the bottom should be read from left to right. The position of the pointer on the dial indicates what the reading should be. If the pointer is between two figures, use the lower figure, e.g. if it is between 7 and 8, use 7. However, if the pointer is between 9 and 0, use 9.

What is a CIU number?

CIU means customer interface unit, it using together with prepaid meter, customer can inquiry electricity and recharge. The communcation between meter and CIU through PLC or MBUS.

How do I find my power meter number?

Your meter number is usually stamped or printed at the bottom of the face plate in BOLD BLACK numerals and can be up to ten digits in length.

How do I get rid of error 30 on my prepaid meter?

Error 30 – Technical error on your meter – please switch your meter off as well as your electricity mains and wait a few minutes. Turn back on and retry the token. If this error 30 persists you should contact your municipality and get a technician to have a look at the meter.

What type of smart meter is a Landis Gyr E470?

Landis & Gyr E470 Smart Electricity Single Phase Meter with Remote Monitoring.

What is a Landis Gyr E470 smart meter?

The E470 uses ZigBee Smart Energy Profile to communicate with other devices such as an In Home Display Unit and for communication with the External Communications Hub via a Home Area Network (HAN).

How do I reset my British Gas electric meter?

Restore my electricity supply using my meter

1. Look at the meter reading screen on your electricity meter.
2. Press A twice.
3. Press B to restore the electricity supply.

How do I reset my prepaid meter?

To reset your prepaid meter, make sure all your appliances are switched off, this is very important. Then Press the ‘I’ key then 008 on the device, a screen will appear showing your consumption days and other information, press the ‘I’ key again twice to reset your prepaid meter.

Why is my prepaid meter showing reject?

WHY DOES MY METER REJECT TOKENS? This may result from using the wrong meter number when vending, a faulty meter or change in tariff index. The customer is required to visit any of our nearest customer care units or contact us through our contact channels(helplines, social media & live chat) for immediate assistance.

How do you manually read a smart meter?

To read the meter:

1. press the middle button – it should say ‘R1’
2. write down the number below ‘IMP’ from left to right – this is usually your night or ‘off-peak’ reading.
3. press the middle button again – it should say ‘R2’
4. write down the number below ‘IMP’ from left to right – this is usually your day or ‘peak’ reading.

How do you read a red and blue gas meter?

If you have A and B buttons
Press either the red ‘A’ or black ‘B’ buttons to wake up the display. Your reading should now be visible on screen. It may display “METER INDEX” Ignore any digits after a decimal point if you have one.

Which smart meter do I have?

The easiest way to tell is to look at your electricity meter. If the serial number starts with 19P, this indicates it’s a SMETS1 meter. If it starts with 19M, then this means it’s SMETS2.

How do you read a gas and electric meter?

To read the meter:

1. Read the first 4 dials from left to right – ignore the large dials or red dials.
2. If the pointer is between two numbers, write down the lower number – if it’s between 9 and 0, write down 9.
3. If the pointer is directly over a number, write down that number.

How do I find my Clou meter number?

The meter number is printed on the meter and on your customer card which you use to buy credit. After successful pairing the display will show OK.