How Do You Program A Hunter Src Sprinkler System?

How do I reset my Hunter SRC controller?

SRC Reset

1. Unplug the controller’s transformer and remove the battery.
2. Press and hold down the , and buttons.
3. Plug the controller’s transformer back in.
4. Release the , and buttons. The display should now show 12:00a. m.
5. All the memory has been cleared and the controller may now be reprogrammed. Reinstall the battery.

How do I reset my hunter water system?

Resetting a Hunter X-Core is easy. To reset the irrigation controller, all you need to do is press the negative, the hand and the program keys at the same time, then use a small tool to press in the small reset button on the side of your controller. A small screwdriver or a pen will do the trick.

How do you adjust a hunter sprinkler head?

Insert the plastic key end of the Hunter wrench into the adjustment socket . While holding the nozzle turret at the right stop, turn the wrench clockwise. Each full 360° turn of the wrench will increase the arc 90°. Adjust to any arc between 40° and 360°.

Why is my controller not starting the watering cycle?

Check for Rain Sensor operation
Look at the “Sensor” terminals on the controller.By sliding the Rain Sensor switch to the “Bypass” position you can over-ride the active sensor. Look at the controller display, if the “Sensor OFF” message is displayed, the sensor is activated and inhibiting the watering cycles.

Why isn’t my hunter sprinkler system working?

If your controller shows irrigation running (Flashing Sprinkler Icon), and your sprinklers are not working, you may have a wiring problem at the valves or the irrigation water supply has been shut down.Check the wiring connections at the master valves for loose or corroded connections, or a bad solenoid.

How do I test my Hunter irrigation system?

To initiate the test program:

1. Press and hold the PRG button. The station number will be flashing.
2. Press the or button to scroll to the station you would like the test program to start with. Use the and buttons to set a run time of up to 15 minutes.
3. After a 2 second pause, the test program will begin.

Is there an app for Hunter sprinkler system?

Hunter Hydrawise
Remote access is possible through either the Hydrawise app (iOS or Android compatible devices) or online through their cloud software. Key product features include: Predictive Watering Adjustments based on web-based weather data brings up to 50 percent in water savings.

How do I reset my sprinklers?

How to Reset a Sprinkler System

1. Turn the control dial to the “off” position.
2. Press the “next” button to access the clear-memory feature.
3. Press and hold the “off” button until the display stops blinking.
4. Turn the control dial to the “run” position.
5. Press and hold down the “minus” arrow and “prog” buttons simultaneously.

How do I reset my hunter X2 sprinkler?

X2 – Total Reset

1. Turn the dial to the RUN position.
2. Press and hold the program button.
3. Press and release the RESET button located inside the lower wiring compartment.
4. When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.

How do you adjust Hunter 1/20 sprinkler heads?

Insert the plastic end of the Hunter adjustment wrench into the arc adjustment socket. While holding the nozzle turret at the right stop, turn the wrench clockwise. Each full 360 degree rotation of the wrench will increase the arc 90 degrees. You can adjust the arc anywhere in between 50 degrees and 360 degrees.

Why is my sprinkler system not getting water?

Your Sprinkler System Is Not Getting Water
If the handle on your backflow valve gets inadvertently shut off, it restricts any water from flowing past the backflow and to the sprinkler system valves. Your rain sensor might be faulty. A wire might have been cut. The timer may be broken.

How do you test a hunter solenoid valve?

Valve Test Procedure:

1. Turn off the water supply to the irrigation system using an isolation valve.
2. Disconnect the solenoid wires from the controller.
3. Using and multimeter test the number of ohms through the solenoid. 20-60 ohms – Good.
4. If solenoid tests Good, then the solenoid is OK.

How do you test a hunter node?

Make sure the controller is in Idle Mode. Press and hold the PRG button until the icon is displayed. The station number will be displayed in the lower left side of the display along with the run time. Quickly press the plus or minus buttons to set the duration of watering time for the test program.