How Do You Make A Curtain Rod Out Of A Wooden Dowel?

Find and mark the center of one end of the dowel. Drill a 3/16 inch hole one inch deep at the center mark. Use pliers to screw one end of the dowel screw into the dowel, then screw the other dowel onto that. Sand and apply clear finish* to dowel rods.

How do you make a homemade curtain rod?

Materials for DIY Curtain Rods

1. 1/2 inch Electrical Conduit – $2 for a 10 foot length.
2. Corner braces – $3 for a pack of 4.
3. 1/2 inch One hole straps – $3 for a pack of 25.
4. Nuts and bolts to attach the straps to the braces – $1.50 for a pack of 5.
5. Spray primer (optional)
6. Spray paint in desired color (optional)

What can I use instead of curtain rod brackets?

An old piece of fence or a coatrack that you don’t use any longer is a great way to create your own DIY curtain rod. Just take a section of fence or rack and hang a few hooks on it to hold your curtains. This is a great rustic d?cor idea and a really cheap one, too.

Can you use wooden dowels for curtain rods?

By styling wooden dowels to look like copper rods, the DIY curtain rods were so inexpensive (just $12 apiece!) that we had money left over to craft statement-making tiebacks to match. Measure your window, then cut the 1-inch wooden dowel to a length at least 5 inches longer than your window is wide.

Can I use a dowel as a curtain rod?

Choose a dowel rod that is slightly longer than your window. For example, the window in the photo example is 40 inches and I used a 48 inch dowel rod. You can get round dowels like this in lengths up to 96 inches – like this one I found at Home Depot.

How can I hang curtains without curtain rods?

For stationary curtains, it’s easy to hang them without a rod using upholstery tacks.
5 Creative Ways to Hang Curtains Without Rods

1. upholstery tacks.
2. tension cables.
3. hook-eye screws and drapery pins.
4. staples and furring strips.
5. cabinet knobs.

Do you need a wooden batten for a curtain pole?

Usually no need for battens if you have a skilled curtain fitter using the correct fittings and a quality pole, even with heavy weight fabric and interlining.

What can I use instead of curtain hooks?

Unique Ways to Hang Your Curtains

1. Make Your Curtain Hardware. These ideas are just a start.
2. Coat Hooks. Brass or metal coat hooks can be attached above your window to hold curtain panels.
3. Glass or Brass Door Knobs.
4. Spoons.
5. Belts.
6. Clothespins.
7. Wire.

How can I hang curtains without putting holes in the wall?

Here are five ways to hang curtains without damaging walls or window frames:

1. Use 3M Command Hooks.
2. Try Kwik-Hang Curtain Rod Brackets.
3. Use Tension Rods.
4. Get Creative With Coat Hooks.
5. Try Magnetic Rods on Metal Doors.

How do you make a finial curtain rod?

These DIY curtain rod pinecone finials add warmth and beauty to a family room, dining room or kitchen. Use corks to connect the pinecones to your curtain rod. Insert the cork into your curtain rod, and use hot glue to attach the pinecone to the cork. That’s it!

Can I make my own dowel pins?

Making dowels is easy to do, and it allows you to use scraps of any material you have on hand.A better method is to use a dowel plate, which lets you make accurately sized, perfectly round dowels in no time.

How much weight can a 1 inch dowel rod hold?

Your 1″ dowel would be approximately 1/3 the strength of the 1.5″ dowels. Their weakest dowel had a safe load of 3,200# with an ultimate failure load of 5,000 – 6,000#. Therefore your safe load will probably be more than 1,000# and almost twice that before it would actually fail.

How do you attach a dowel rod?

1. Drill 3/16″ holes into the center of the two dowel ends to be connected.
2. Insert the fastener into the end of one of the dowels and turn to the left until the screw is about half way into the first dowel.
3. Insert the exposed fastener end into the second dowel and turn to the left to tighten.