How Do You Light A Water Heater With Electronic Pilot Ao Smith?

Can you manually light a water heater with electronic pilot?

* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system.If the pilot light will not re-light, the problem could be a clogged pilot line or orifice, or gas is not reaching the water heater.

How do you light the pilot on a hot water heater?

How to Light a Water Heater Pilot Light

  1. Open the door/cover over the pilot light access.
  2. Use a flashlight or a headlamp to find the burner inside.
  3. Turn the gas knob to “Pilot,” press and hold it down.
  4. While still holding the gas down, light that pilot.

How do you light a gas and electric water heater?

Lighting A Hot Water Heater Pilot Light

  1. Set the temperature control. to its lowest setting.
  2. Set the on-off control. to the pilot setting.
  3. Press the hot water heater. pilot button down and. hold it.
  4. While looking through the the sight glass slowly press the spark generator until you here it click. You should see a spark.

How do you light an electric pilot light?

Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately. If you have a spark igniter, press the ignition button until the pilot flame ignites.

How do you manually light an electric water heater?

Lighting the Pilot Light on an Automatic Hot Water Heater
All you have to do is hold the pilot knob down for 30 seconds and hold the ignition button at the same time. You do not need to use a lighter. Your pilot light will turn on!

See also  How Good Is Somfy?

How do you light a gas heater with electronic pilot?

If you have a gas furnace, here are the steps on how to light a pilot light.

  1. First, locate the pilot valve on the furnace.
  2. Find the gas valve and turn it to the “off” position.
  3. Turn the valve to the “pilot” position.
  4. Press and hold the reset button.
  5. If the reset button fails, ignite the lighter.

Where is the pilot light on an electric water heater?

Your hot water heater pilot light can usually be found beneath the water tank on your unit. You may need to remove an access panel to access it. Some newer models may have the pilot light behind a glass panel. The casing for the pilot light should look like a small silver tube.

Do AO Smith water heaters have a pilot light?

Smith water heater. Occasionally, the pilot light on your A.O.Smith water heaters, including the Conservationist model, use a modern built-in piezoelectric igniter system that allows you to light the pilot by pushing the ignition button.

Is there a reset button on an electric hot water heater?

Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.

How do you light a water heater after a flood?

Turn the gas supply back on, turn the dial on the gas valve to the “pilot” position and depress the push-button pilot button as you light the pilot under the burner with the log lighter. Hold the pilot button down to “prime” the thermocouple—otherwise it will cut the gas supply to the pilot light.

See also  What Does Lte Mean On My Phone?

What does it mean when your pilot light won’t stay lit?

thermocouple
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.

Does electric heater have pilot light?

Although today’s standard electric furnace uses a hot surface ignition, older models often use an intermittent pilot to ignite heat.If you can’t get the pilot in your electric furnace to light, it’s usually a simple matter to turn it back on.

How do I turn on electric heater?

  1. Step 1: Locate the Pilot Light. In some heaters, it is easy to locate the pilot light, as it is just behind the heater vent.
  2. Step 2: Ignition Process. Electric Heaters.
  3. Step 3: Set the temperature. Once your heater is turned on, set the heater on your desired temperature using the electric thermostat.

How do I turn on my electric water heater?

Follow these steps to turn on your electric water heater:

  1. Step 1: Check for Any Open Valves, or Faucets Close Them Up.
  2. Step 2: Turn the Cold Water On.
  3. Step 3: Take Out the Safety Tag.
  4. Step 4: Turn on the Breaker.

Should the pilot light always be on in a gas water heater?

The thermocouple’s job is to shut a gas safety valve if the pilot light goes out. That’s important because gas is always being supplied to the pilot to keep the flame lit. But if the pilot flame goes out, then the gas would still be released. After a while, the gas could collect in your home and become a health hazard.

See also  How Do I See Bandwidth Usage On Mac?

How do I know if my pilot light is out?

How to Tell If the Pilot Light Is Out

  1. Locate the front cover panel on your furnace. It should be a little door that’s easily visible.
  2. If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame.
  3. If you don’t see a flame, your pilot light is out.
  4. If there is a flame, check the color.

Contents

This entry was posted in Smart Home by Claire Hampton. Bookmark the permalink.
Avatar photo

About Claire Hampton

Claire Hampton is a lover of smart devices. She has an innate curiosity and love for anything that makes life easier and more efficient. Claire is always on the lookout for the latest and greatest in technology, and loves trying out new gadgets and apps.