How Do You Install A Traverse Rod Carrier Slide?

How do you put a slider on a traverse rod?

Install the new slide by placing the string into the reel and then setting the slide into the rod, pressing inward just as you did to remove it. Slide it into the rod until it is securely in place. Continue inserting slides in this manner until you have replaced all that you need for your drapes.

How do you convert Tab back curtains to traverse rods?

If you want to use a traverse rod, that opens and closes with the pull of a cord, you need to alter your tab-back panels to accept a drapery pin. Just by making a small single-finger pleat, the curtains can accept a pin and hold the folds in place as the curtains are opened and closed on a traverse rod.

How do you use regular curtains on a traverse rod?

How do you hang curtains on a traverse rod?

1. First, fold the curtain’s pleats in an accordion like manner.
2. Hook the first pin in the first hole and the second pin on the last hole of the carrier.
3. Crease the curtain’s pleats at the seam.
4. Lastly, attach the two remaining pins at the end of the rod.

How does a traverse rod work?

How do Traverse Curtain Rods Work? These mechanical rods operate by using small clips that move along a track that is embedded in the rod itself. This allows the curtain or drape to move smoothly along the rod and prevents any snagging that may happen with traditional curtain rods.

How do corded curtain tracks work?

Corded curtain tracks, they do what they say on the tin. The have a cord to the side of the track which you pull to open and close the curtains. This cord should always be secured to the wall and a minimum of 1.5m from the ground – this will ensure that a child will not be able to get entangled in the cord.

What is a two way traverse rod?

Curtain rods with two operable layers of fabric are called double traverse rods.For a stronger double rod, visit our heavy-duty curtain rods section.

What is a one way draw curtain rod?

One-way draw drapes allow you to open your curtains to one side of the windows.A one-way draw curtain rod can be purchased at home improvement stores or anywhere that drapery hardware is sold. As you select your one-way draw curtain rod, make sure you select one long enough for your window treatment.

How do you hang pocket curtains on a traverse rod?

1. Mount the traverse rod supports and bracket according to the packaging instructions. Hang the rod in the supports and brackets.
2. Measure the width of your curtain panels. Cut a piece of pleater tape to this size.
3. Lay the curtains flat, wrong side up.
4. Carry one curtain panel at a time to the traverse rod.

How do you put a glider on a curtain track?

A good way of spacing your gliders and ensuring you have enough prior to adding them to your curtain track is to lay your curtains on the floor or any flat surface. You can then place the gliders just above the curtains allowing you to space them out evenly and count the number of gliders needed along your track.

What kind of curtains do you put on a traverse rod?

Curtains for a traverse rod are referred to as pinch pleat curtains. They require the use of special curtain pins to hang (pins are often included with drapes, but not always). The best way to find traverse curtains is to consult a drapery professional, as they are often a special-order item.

Can you hang back tab curtains with hooks?

Many drapes come with back tabs where you can clip the rings, or you can pinch the fabric to create pleats.When using drapery hooks, you have to make sure the hook does not go through to the front of the drape. You only want it to grab the back tab or lining. Thread the hole in the ring through the hook to attach.

Do you need middle bracket on curtain rod?

Most rods require support brackets every 30 to 36 inches. If your window is longer than 60 inches across, you’ll need two center support brackets. You can get single or double center support brackets depending if you’re hanging one or two layers of curtains.

How are traverse rods measured?

Standard traverse rods are only used for pleated draperies. Measure the width of the rod from end to end, this is the face width or rod width. At the ends of the rod, measure the distance from the front of the rod to the wall, this is the return.Measure from the top of the rod to your desired length.

How do you fix a pulley on a curtain?

Unscrew the brackets that hold the rod in place and take the rod down. Pull the cord from the rod, cutting it free from any tangles. Place the rod with the hardware facing up and feed the new cord under the top pulley on the left end of the rod. Maneuver the new cord into the rod’s track and through the opening.