Lift off the outer door of your Rheem water heater. Rotate the gas knob counter-clockwise until it is in the Pilot Light position. Press down on the red button to the left of the gas knob. On the left of the gas knob is the piezo ignitor striker.
How do you light the pilot on a Rheem water heater?
Push down the red button to the left of the gas knob. Hold the red button down while pressing the piezo ignitor striker, found to the immediate right of the gas knob, repeatedly until the pilot is lit. You can see the pilot light through the viewing window on the water-heater’s inner door.
Do all new gas water heaters have electronic ignition?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system.
How do you light a gas water heater?
Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.
How do you light the pilot on a gas water heater?
How to Light a Water Heater Pilot Light
- Open the door/cover over the pilot light access.
- Use a flashlight or a headlamp to find the burner inside.
- Turn the gas knob to Pilot, press and hold it down.
- While still holding the gas down, light that pilot.
How long does it take for a Rheem water heater to heat up?
The average gas heater takes between 30 and 40 minutes to fully heat up the water in its tank. The average electric heater takes about twice as long as the average gas heater to fully heat up the water in its tank, so you can expect it to take between an hour and an hour and 20 minutes to heat up.
How do you light a pilot light?
If you have a gas furnace, here are the steps on how to light a pilot light.
- First, locate the pilot valve on the furnace.
- Find the gas valve and turn it to the “off” position.
- Turn the valve to the pilot position.
- Press and hold the reset button.
- If the reset button fails, ignite the lighter.
Do gas water heaters have a pilot light?
Tank-type gas water heaters use a pilot light to ignite the gas burner when the water in the tank needs to be heated. Usually, the first warning that your pilot light has gone out is the cold water coming from the hot water tap.If your heater’s pilot goes out, you can relight it yourself.
How does an electronic ignition water heater work?
An electronic gas ignition system utilizes solid-state controls for igniting the flame and proving the flame. Electronic ignition gas systems do not use a thermocouple or thermopile to prove the flame. Electronic ignition gas ignition systems use a flame sensor that measures microamps to prove the flame.
What is continuous pilot?
A standing pilot is the standard ignition device for most natural gas burning heating systems, and has been for many years. It’s a continuously burning flame at the bottom of the heater, responsible for starting the burners that actually generate heat for the home.
Should the water heater be on pilot or on?
You should set the water heater to pilot. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.
What do I do if my water heater won’t light?
If you have a natural or propane gas water heater, chances are the pilot has gone out.If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
What setting should my Rheem water heater be on?
120°F.
Tank Water Heating
Residential tank water heaters typically store between 20 and 80 gallons of hot water hot throughout, usually at the factory setting of 120°F. The temperature can be adjusted up or down by a control on the unit.
How do I reset my Rheem water heater?
Turn the water heater’s gas valve switch to the “OFF” position, wait for a few seconds and then flip the switch to the “ON” position to reset the system.
How long does it take a 50 gallon gas water heater to heat up?
Gas Hot Water Heater Recovery
Water coming into a 50-gallon tank at 40 degrees takes just 53 1/2 minutes to reach 120 degrees. For 60-degree water entering the tank, calculate about 40 minutes needed for the water to reach the 120-degree temperature. For 70-degree water, it would take 33 minutes.
How do I know if my pilot light is out on my water heater?
When a water heater pilot light goes out, it usually means that a natural change in gas pressure extinguished the flame. The main sign that a pilot light is out is one that everyone dreads: The water won’t get hot.
What does a pilot light look like?
Inspecting a Gas Furnace Pilot Light Flame
A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.
What do you do if your pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
How do you manually light a Rheem water heater?
A Rheem water heater pilot light needs to be lit manually using the piezo ignitor striker built into the water heater.
- Rotate the gas knob on your Rheem water heater clockwise until it is in position.
- Rotate the water-heater temperature dial counter-clockwise until it is set to the lowest temperature setting.
Will the gas company light My pilot?
Absolutely! We can send a gas service technician to light your pilot, and conduct a gas safety check of your gas fireplace or any other gas appliance to ensure your safety.
Contents