To reset the boiler, turn the selector switch to the R (Reset) position. Hold for at least 5 seconds and release. The fault code will be replaced with the boiler’s current temperature. At this point on a neon indicator boiler model, the flame failure light will stop flashing and will be replaced with the burner light.
What do you do when your boiler says flame failure?
If Flame Failure occurs frequently consult your Installer. This indicates that the Burner has fired up and is heating your system. This indicates that there is electricity to the Boiler. Turn the Central Heating Control Knob clockwise to increase or anticlockwise to decrease the boiler flow temperature.
What causes flame failure on a boiler?
Delayed ignition can be caused by a range of problems, including a restricted or weak pilot light. Also, low gas supply pressure can mean that there is too little gas at the burners, resulting in ignition problems. Another possible cause is too much primary air. This is air that’s mixed with gas before it’s ignited.
How do I get the flame back on my boiler?
How do you relight the pilot light on a boiler?
- Turn the gas to ‘pilot. ‘
- Press and hold the reset switch for one minute and hold a flame to the pilot light at the same time.
- If all is working as expected, return any casing/doors and turn the gas from ‘pilot’ to ‘on.
What are the common causes of burner ignition failure or flame failure?
The flame failure trip in a typical boiler can be due to one of the following reasons: loss of ignition; fuel valve closed, unstable flame, low airflow, very high furnace pressure, dirty flame sensor and loss of electrical supply.
What does a false flame mean on a boiler?
According to Potterton, the E384 boiler fault code relates to a false flame. Essentially, the boiler’s printed circuit board (PCB) either thinks there is a flame when there shouldn’t be, such as when the gas valve should be closed.
What does the flame mean on a boiler?
When you look and see the flame inside your boiler it should be burning with a blue flame. If it is burning with a yellow flame, this could be a sign that carbon monoxide is being produce.
How does flame failure device work?
Your Flame Failure Device is a key safety feature for your cooker. It is responsible for stopping the flow of gas to the burner of your gas cooker if the flame has been extinguished for any reason. This will prevent the build-up of harmful gas inside your cooker and kitchen.
How do you ignite a Baxi boiler?
To light the pilot: Looking through the pilot viewing window press the gas control knob fully inwards and hold. Press in igniter button and release. Repeat until pilot ignites. Continue to hold in gas control knob for approximately 15 seconds and then release.
How do you fix a boiler that won’t ignite?
If you still can’t light your boiler, there could be debris blocking the jet. Boiler pilot light jets are relatively cheap to replace but can also be removed, cleaned and re-installed. Your heating engineer will be able to advise you on the best course of action and replace the jet accordingly.
What happens when your pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
How do you fix a yellow flame on a gas boiler?
Turn off your boiler and make sure the pilot light is off. You can then give the pilot tube a clean with a nail, needle or other thin object but take care not to damage it. Once it’s clean, you can then turn your boiler back on and reset the pilot light.
Why is my pilot light flame yellow?
The most common reason why a pilot light would start to burn yellow is that the air intake valve to the pilot light is clogged with dirt.If there is a small amount of dirt blocking the air, the yellow color might only be at the tip of the flame. If there is a large amount of dirt, the entire flame will burn yellow.
Should my boiler flame be on all the time?
The pilot light is the blue flame that always stays lit under your boiler.When heat is required, the pilot light will inflame that gas and send it to the burners. The pilot light must always stay on or gas will easily escape. If the pilot light keeps turning off, then your boiler is not working.
Do I need a flame failure device?
The flame failure device is a critically important part of any gas cooker. If the cooker’s flame goes out, the flame failure device is responsible for ensuring that the flow of gas to the cooker is cut off – a crucial safety measure that prevents the build-up of dangerous flammable gas.
Is a thermocouple a flame failure device?
Your cooker’s Flame Failure Device (FFD) or thermocouple is a key safety feature that stems the flow of gas when your cooker’s flame is extinguished for any reason.
Why does my Baxi boiler keep locking out?
Common causes of a Baxi boiler locking out include overheating (110), fan fault (160), flue overheating (E131) and an issue with the printed circuit board (PCB) (E168).
Most Baxi boilers have a simple reset button on the front panel – locate this and press and hold the button for 1 to 3 seconds or until it’s clear that the boiler has rebooted itself. Fed up of fixing you BAXI?
Can you manually ignite a boiler?
If there is no label, look at the top of the gas control knob. If the control knob has two settings, on and off, it is an automatic ignition system. A manual ignition will have three settings — on, off and pilot. Never attempt to light an automatic ignition system manually.
Why will my boiler not stay lit?
If it’s not staying lit though, then you’re probably dealing with a thermocouple issue. The thermocouple of a boiler system is a long metal wire that acts as a heat sensor for the pilot light.If the pilot light goes out, then the electrical current stops, and the gas valve closes.
What do you do if your pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Contents