How Do I Wake Up My Gas Smart Meter?

Taking readings on your smart meter To take the reading from your gas meter, you’ll need to press a button to wake up the meter. Depending on your meter, it’ll be either an OK button, a red “A” button or a round button between two arrowed buttons. The reading will appear on the screen.

How do I turn my gas smart meter back on?

Here’s how to do it:

1. Safety first. Make sure all your gas appliances are turned off.
2. When your gas meter is ready to connect, it’ll say PUSH TO RECONNECT.
3. Press any button, and it’ll automatically begin to reconnect (this may take a few minutes).

How do I turn on my smart meter?

Press and hold the ‘B’ button for around 2 seconds, until you see a message saying ‘Supply enabled’. Your meter is now online again, and the gas or electricity supply to your home will be restored.

Why is my smart meter not showing gas?

My smart energy monitor has gone blank
Unplug your smart energy monitor. Move it closer to your electricity meter. Plug your smart energy monitor back in. Wait seven days (most smart energy monitors re-start automatically within a week)

How do I reconnect my smart meter?

To restore the lost connection to your smart meter, you’ll need to:

1. Take your In-Home Display to where your electricity meter is located.
2. Once you’re close to the meter, hold down the “OK button” until the In-Home Display turns off and then on again.
3. You should then see the message: “your smart meter is now paired”.

How do I turn my gas back on after disconnecting?

You are going to need a wrench or gas shut off tool to do this. Very slowly, turn the meter back into the on position. The lever should be in line with the pipe after making a ninety-degree turn. Finally, you can re-light any of the pilot lights in your appliances.

How do you turn on the gas on a British gas smart meter?

My meter has turned off

1. Ensure that all gas appliances are switched off.
2. Press button A on your gas meter to wake the screen.
3. Press B on your gas meter.
4. Press and hold A until you hear the supply come on.

How do I reset my smart meter?

To reset it it turn it right off by holding down the power button for 10 seconds and then power it back on again, it should work.

Why is my smart meter not showing electric?

Try moving your In-Home Display closer to your electricity smart meter. Once you’re there, turn it off using the round, flat button at the back. Wait a minute and then press the button again to switch the IHD back on. Sometimes, this gives it the boost it needs to get going again.

How do I turn on my gas supply on my smart meter SSE?

Press and hold the ( OK ) button on the main Prepay screen. Press the ( OK ) button to scroll through the menu until you reach Info—Supply. Then press and hold the ( OK ) button to enter. Press and hold the ( OK ) button to re-enable supply.

How do you reset a smart meter bulb?

In this article:

1. Unplug the IHD and let it run out of power completely.
2. Leaving the IHD unplugged, restart it by pressing the round, flat button on the back.
3. Let the emergency power reserve run out completely.
4. Plug the IHD in to recharge it, then switch it back on.

How do I reconnect my gas smart meter Eon?

Once you’re back in credit your electricity supply will automatically reconnect. To get your gas supply back on you’ll need to press ‘B’ on your meter followed by ‘A’ and then ‘B’ within 30 seconds of each other.

Can you turn your gas back on yourself?

NOTE: Once you have shut off the gas at the meter, do not try to turn it back on yourself. If the gas service shutoff valve is closed, PG&E or another qualified professional should perform a safety inspection before the gas service is restored and appliance pilots are relit.

What do you do when your gas gets shut off?

If your gas is shut off, turn the gas shutoff valves on all gas appliances to the “off” position until the gas service is restored. Use a flashlight to locate the valve if you cannot find it. To turn off the valve, rotate it clockwise until the valve stops turning.

How do I turn on my British Gas emergency gas?

Using Emergency Credit on my smart energy monitor

1. Go to the home screen on your smart energy monitor.
2. Press Menu.
3. Choose the fuel you want emergency credit for and press Select.
4. Scroll to Emergency and press Select.
5. Press the Accept button.
6. The screen will then show Accepted.

How do I know if my smart meter is faulty?

If the meter stops, turn on 1 appliance at a time and check the meter. If the meter starts to move very quickly, the appliance could be faulty. If the meter is still moving, it’s probably faulty.