On the Categories screen, tap Sensors & Zones. On the Sensors & Zones screen, tap Delete Sensor. Enter the Premise Passphrase and tap Done. Tap the sensor you want to delete, then tap Yes to confirm.
How do you bypass the Comcast door Sensor?
To bypass individual Sensors (also called “zones”), tap Turn Zone Off next to the Sensor to bypass. If you bypass a Sensor, it won’t trigger an alarm when the system is armed. For example, if you bypass the side door Sensor and then arm your system, someone entering through the side door won’t trigger an alarm.
How do I fix my Comcast window Sensor?
Restart the Door/Window Sensor by removing its battery, waiting a few seconds, then reinsert the battery. If the message remains, replace the battery with a fresh battery. If the problem is not resolved, it may be caused by an issue with your touchscreen’s location.
How do you reset a door sensor?
instructions:
- Take off the Sensor’s cover and remove battery.
- Touch the Sensor’s body with a magnet.
- Insert the battery.
- Within 2 seconds remove the magnet from the Sensor’s body, the LED will turn off.
- Remove the battery.
- Re-install the battery.
- Reset will be confirmed by LED blinking.
How do you reset a window sensor?
instructions:
- Take off the Sensor’s cover and remove battery.
- Touch the Sensor’s body with a magnet.
- Insert the battery.
- Within 2 seconds remove the magnet from the Sensor’s body, the LED will turn off.
- Remove the battery.
- Re-install the battery.
- Reset will be confirmed by LED blinking.
How do I test my Comcast motion sensor?
Motion Sensors
- Make sure your system is disarmed.
- Use the touchscreen to bypass the Motion Sensor.
- Make sure there is no movement in the area for two minutes.
- Walk in front of the Sensor, then check your system activity in the Xfinity Home app to see if the motion event was detected.
What is a sensor jamming warning?
Sensor Communication Jammed. Touchscreen communication with the identified sensor is being jammed. Most likely, someone is using a device designed to scramble the radio frequency (RF) signal of the sensors. This could be a burglary in progress. Contact Customer Support.
What does sensor bypassed mean?
To bypass a sensor means to deactivate sensors in one area of your home while leaving the rest of your sensors active. Bypassed sensors are deactivated even while your system is armed. This allows you and your family to move freely throughout the deactivated zone without triggering your alarms.
What does sensor open mean?
If your door or window is closed but the keypad is reporting it open, this means your sensor is out of alignment.This can also mean your sensor or magnet has fallen off the door or frame.
How do you open a door without the alarm going off?
Take the hand mirror and place it across the beam of light guarding the door. This will cause the light beam to break and reflect back on itself. This should allow you to open the door without the alarm going off.
How do I reconnect my motion sensor ring?
Factory Reset your Motion Detector:
- Ensure the battery is inserted and the cover is completely closed.
- Press and hold the reset button under the pinhole found on the back of the device. A paperclip works well.
- The LED on the front of the sensor should begin blinking. Hold the button down until the LED stops blinking.
Does Xfinity Home have glass break sensors?
Between those partnerships and its own products, Xfinity is able to offer a pretty comprehensive selection of home security devices. The company has even added glass break detectors as an add-on option since our last review.
Does Xfinity monitor fire?
Xfinity Home Smoke Monitoring uses Smoke and Heat Detectors that, together with your primary system, are designed to keep your property safe. When an alarm is triggered, our Smoke Detectors alert the Central Monitoring Station, which will notify appropriate emergency personnel for you, even if you aren’t at home.
How do I reset my visonic door sensor?
may have to exclude device if paired with something else. to reset to defaults you pull battery, press and hold tamper switch for 4 sec after reinserting battery. should blink 3 times every 5 sec when in pairing mode I believe.
The device’s red LED turns on solid to indicate the device was removed from the network. 1. To restore Ring Alarm Contact Sensor to factory default settings, locate the pinhole reset button on the device. This is found inside the battery compartment on the back of the device after removing the back bracket.
Why does my Xfinity alarm keep going off?
Change batteries in Sensors and Detectors as soon as you get a low battery alert. Don’t ignore low battery alerts from your Sensors. Failing batteries can cause false alarms.Learn how to replace the batteries for your Xfinity Home devices.
How do you test a motion sensor?
Walk across the sensors field of view, the LED will illuminate when it detects motion. It is best to walk across the sensor, rather than directly towards the sensor. The sensor will repeat this process of waiting 30 seconds then lighting up as it sees motion. It will stay in the test mode for 3 minutes.
How do I turn off the chime on my Xfinity Home?
How do I turn the Door Chime on my TCH or UEI Keypad on or off? The Door Chime signals when a door with a Sensor is opened or closed. Press and hold the 8 button until you get a confirmation beep (~2 seconds) to toggle the chime on or off.
How do I reset my Xfinity Security touch screen?
Remove the battery cover from the back by inserting your finger in the hole and pulling down. Remove the battery and unplug the power cord. Wait 10 seconds and replace the battery and plug in the power cord. This will restart the touchscreen.
How do thieves disable alarms?
While a home invader can’t cut alarm wires to disable a wireless alarm system, there is a tactic called crash and smash whereby a thief could crash into your house via a window or door and smash your security system before the alarm company can be notified.
What is a PIM sensor Xfinity?
OpenHome Converge Panel Interface Module (PIM) is a professional state-of-the-art device that allows you to manage your wired system and its sensors from your TouchScreen.
Contents