How Do I Silence My Alaris Pump?

To silence safety alarm tone, press the SILENCE key. The Alaris PCA module will remain silent.

How do I stop my Alaris pump from beeping?

To resolve: Push the run/pause button to silence the alarm. Gently press on the top of the cassette (top of pump) Push the run/pause button again to restart the pump.

Why does my IV keep beeping?

Your pump may alarm or “beep” for a number of reasons. It will alarm if a medicine is finished infusing or if the pump detects a blockage or air in the line. Always call your nurse when the pump starts to alarm. Do not try to silence the alarm or fix the problem yourself.

How do you pause an IV pump?

To interrupt or pause an infusion, press RUN/PAUSE key.

How do I make my IV stop beeping?

The empty container message means the IV bag is empty and the infusion is complete. Press silence to make the alarm stop beeping. Then press stop. Hold the on/off button for two seconds to turn the pump off.

What do I do if my IV pump goes off?

If there is air, disconnect IV tubing from patient and press the Prime key to remove the air from IV tubing, Reconnect the IV tubing to the patient’s catheter. Clean Bubble Detector with a damp Q-Tip (use water only). Press OK key to resume infusion.

What are the three major problems of infusion pumps?

The FDA has summarized the three major reasons for infusion pump malfunctions as the following:

• Software Defects. Some pumps fail to activate pre-programmed alarms when problems occur, while others activate an alarm in the absence of a problem.
• User Interface Issues.
• Mechanical or Electrical Failures.

Does IV go in artery or vein?

IVs are always placed in veins, not arteries, allowing the medication to move through the bloodstream to the heart. Learn more about IVs by reading 10 Commonly Asked IV Therapy Questions.

What does open vein mean on IV pump?

HI PRESSURE-There is a blockage somewhere from the pump to the patient’s catheter not allowing the fluids to run.FIN/OPEN/VEIN-The preset VTBI has been completed and the pump has changed to a TKO (To Keep Open) mode. The pump will continue to infuse a small amount of fluids to keep the catheter patent.

How do you unlock the Alaris pump panel?

Alaris® System
Press and hold the Tamper Resistance Control on the rear of the Alaris PC unit for three seconds. 2. When the keypad is unlocked, a PANEL UNLOCKED prompt displays on the main screen of the Alaris PC unit. The PANEL UNLOCKED prompt remains on the screen for three seconds.

How do I change the pressure on my Alaris pump?

1) Press Channel Select on the channel you wish to adjust the pressure limit. 2) Press Options. The Pressure Limit Selection screen will display the pressure limit options: Pump and Selectable. 3) Select the Selectable option.

How does the Alaris pump work?

How Do Alaris Pumps Work? Alaris infusion pumps come with a PCU, or point of care unit, and can be customized with up to four modules. These modules are connected to tubes and bags of medicine or other fluids. The modules work together with the PCU to perform a variety of functions.

What does continuous infusion mean?

Listen to pronunciation. (kon-TIN-yoo-us in-FYOO-zhun) The administration of a fluid into a blood vessel, usually over a prolonged period of time.

How do you fix IV occlusion?

What Should I Do If My Pump Reads “Down Occlusion”

1. Check clamp on tubing and unclamp if clamped.
2. Check tubing for any kinks or if patient is lying on tubing causing it to occlude.
3. Make sure tubing is placed in pump correctly.
4. Try to restart by pressing Pause/Yes to Resume/Run to Start.

What does it mean when an IV is occluded?

Occlusion is the interruption or ineffective therapy of infusion due to a blockage, momentary closure or obstruction of the passageway or blood vessel.

What is occluded patient?

An occlusion is a complete or partial blockage of a blood vessel.

How do you troubleshoot an IV pump?

Infusion Pump Alarm Solutions:

1. Check your device for reconfiguration. Oftentimes your pump can be reconfigured to make it less sensitive to arm movement.
2. Warming the medication to room temperature.
3. Avoid “burping” IV bags.
4. Slowly prime the IV set.
5. If your pump beeps, stop all lines, check your settings and restart!

How do infusion pump alarms work?

Infusion pump alarms are defined as those device alarms that provide continual or repeating auditory and visual notification, requiring the clinician to intervene to address and silence the alarm.

What is distal occlusion on IV pump?

One of the most common infusion pump alarms is for air in the IV line.Another common infusion pump alarm is a distal occlusion alarm, which is often caused by the patient kinking the line by bending an arm or catching the loose tubing on the bed.

What is the difference between infusion pump and syringe pump?

An infusion pump draws fluid from a standard bag of intravenous fluid and controls the rate of flow.A syringe pump is a different type of infusion delivery device. Instead of drawing fluid from an infusion bag, intravenous medications are drawn into a syringe and installed into the device.

What are the complications of infusion pump?

Examples of Reported Infusion Pump Problems

• Software problems.
• Alarm errors.
• Inadequate user interface design (“human factors” issues)
• Broken components.
• Battery failures.
• Fire, sparks, charring, or shocks.