How Do I Restart Ecobee After Power Outage?

Open the panel on your furnace to expose the control panel where your thermostat wires are connected. Most systems have a purple 3 or an orange 5 amp fuse on the board—check this fuse to ensure that it’s intact. A blown fuse will have to be replaced. Once a blown fuse is replaced, the ecobee should power back on.

How do I reset my Ecobee thermostat after power outage?

1 Factory Reset

  1. From the Home screen, press Menu.
  2. Select Settings.
  3. Go to Reset.
  4. Choose Reset All Settings then confirm your selection by pressing Yes.
  5. Choose the reset option that suits your needs:
  6. The ecobee thermostat will be reset to factory defaults.

Is there a way to restart ecobee?

1 Reboot

  1. Push and hold the main button on your Ecobee Switch+.
  2. Continue to hold the main switch for five seconds.
  3. Wait for the voice prompt to say “Restart Device”.
  4. Press the main button one time.
  5. Your Ecobee Switch+ will restart, and should be ready to use again in a few minutes.

How do you reset a thermostat after a power outage?

How to Reset Your Air Conditioner After a Power Outage

  1. Turn Off Your AC at the Thermostat. The first thing you need to do is to shut the system off at the thermostat.
  2. Turn Off Your AC at the Circuit Breaker.
  3. Turn Your AC Back On at the Circuit Breaker.
  4. Wait for 30 Minutes.
  5. Turn Your AC Back On at the Thermostat.

How do I get ecobee back online?

If it’s not showing as connected to ecobee.com, follow the steps below:

  1. Try power-cycling the ecobee by removing it from the wall and leaving it off for two minutes.
  2. After two minutes, place the ecobee back on the wall.
  3. To reconnect to Wi-Fi, go to MAIN MENU > SETTINGS > WI-FI > NETWORK > SELECT WI-FI NETWORK.
See also  Are Digital Thermostats Better Than Mercury?

Why isn’t my AC working after power outage?

Usually, the 3 main reasons your AC won’t blow cold air after a power outage include: A tripped circuit breaker. A bad capacitor. Compressor failure.

What happens if ecobee loses power?

If this power supply is interrupted, the ecobee will not power back on until 24VAC is restored. When the ecobee thermostat loses power during heating or cooling, it is often due to one of the following: A safety feature on the HVAC (Heating, Ventilation, and Cooling) system triggering, cutting power to the thermostat.

How do I turn on ecobee AC?

The cooling set point is blue while the heating set point is orange. To enable this system mode, go to Main Menu > Settings > Installation Settings > Thresholds > Auto Heat/Cool and select Enable.

How do I unplug my ecobee?

To remove the ecobee backplate, carefully remove your thermostat from the backplate by putting your thumb and index finger on the backplate. Then, pull against the ecobee3 lite. Remove the screws from the backplate to remove it from the wall.

Do you have to reset AC after power outage?

Your AC needs some time to reset its internal circuit breaker after a power outage.That’s why it’s so important to keep the thermostat in the “off” position during this time, because the internal breaker cannot reset if the thermostat is calling for cooling.

Can a power outage damage a thermostat?

If the thermostat setting is calling for cooling when the power is restored, the surge caused by a restoration of electricity can damage the heating, ventilating, and air conditioning system.

How do I reconnect my ecobee thermostat?

To connect your Ecobee thermostat to your Wi-Fi network:

  1. From the Home screen, press Menu.
  2. Then select Settings.
  3. Go to Wi-Fi.
  4. Make sure Wi-Fi Radio is Enabled.
  5. Go to Network.
  6. Tap on Select Wi-Fi Network.
  7. Pick your Wi-Fi network from the list and enter your Wi-Fi password if required.
  8. Tap OK to exit.
See also  Should You Close Your Blinds On A Hot Day?

Why does my ecobee go offline?

During this process, we may change channels on either 5Ghz or 2.4Ghz, or both bands based on various factors. Ecobee fails to switch to the new channels after optimization. This causes the device to disconnect and at times, fail to connect back until Ecobee is manually reconnected to the Wi-Fi network.

Does my ecobee have a battery?

The Ecobee comes with one wireless sensor, which is powered by a CR2032 coin-cell battery; the company says it should last about 4 years. When the battery runs low, you’ll receive an alert.

How do you restart an air conditioner after a power outage?

How to restart your air conditioner after a power outage

  1. Turn off your air conditioner at the thermostat.
  2. Turn off your air conditioner at the circuit breaker.
  3. Turn your air conditioner back on at the circuit breaker.
  4. Wait for 30 minutes.
  5. Turn your air conditioner back on at the thermostat.

Where is AC reset button?

An AC’s reset button is typically red and visible, so it should be easy to spot. If you don’t see a reset button on the outside, it could be located inside the unit behind the service panel. Before poking around inside the machinery, be sure to cut power to the system by flipping off your circuit breaker.

How do I reset my air conditioner?

How to Reset an Air Conditioner

  1. Power down your AC. Start at your circuit breaker panel and flip the breaker that powers your AC.
  2. Find the button. Most air conditioning units are equipped with a reset button.
  3. Hold down the reset button for 3 to 5 seconds and then release.
  4. Restore power to your AC.
See also  What Does The Whirlpool App Do?

How do I change the battery in my ecobee?

Change the Battery

  1. Place your thumb and index finger on the narrow part of the sensor stand, and your other hand on the front of the sensor.
  2. Gently pull upwards to release the sensor.
  3. Remove the battery by gently prying it out of the battery compartment with a thin tool such as a pen, plastic card, or screwdriver.

Why is my ecobee not turning on my AC?

The most common cause of your air conditioner not turning on is an excessive build-up of water from condensation within your HVAC system. Your HVAC system has a drain pan or drain line.Some signs that you have a backed-up drain pan or drain line are: Your ecobee thermostat is powered off or is frequently rebooting.

Why will my AC not turn on?

If your AC unit won’t turn on, the first thing you should check is if there was a blown fuse or a tripped breaker. There’s a good chance that the problem is a tripped breaker if the circuit was overloaded.However, it is also possible that a power surge caused your air conditioner to blow a fuse or trip a breaker.

How long does ecobee take to activate?

Upon powering up the ecobee, it will provide step-by-step prompts to assist with the HVAC equipment configuration. The ecobee will first start with the temperature sensor calibration—this can take up to 20 minutes before you can resume with the thermostat configuration.

Contents

This entry was posted in Smart Home by Silvia Barton. Bookmark the permalink.
Avatar photo

About Silvia Barton

Silvia Barton is someone who really enjoys smart devices. She thinks they make life a lot easier and more fun. Silvia loves to try out new gadgets and she's always on the lookout for the latest and greatest thing in the world of technology.