How do I reset my Honeywell Z-wave switch?
Reset to factory default
Quickly press ON (Top) button three (3) times then immediatelypress the OFF (Bottom) button three (3) times. The LED will flashON/OFF 5 times when completed successfully.
How do I reset my GE smart toggle switch?
1 Reset Smart Switch
Press and hold your switch’s button, toggle, or paddle for 10 seconds. If the reset is successful, the indicator light will begin blinking blue meaning the switch is ready to be set up again.
How do I reset my Z-wave device?
1) Press and hold the Aeotec Z-Wave device for 20 seconds, then release to perform a Hard Reset.
How do I reset my GE Z-wave outlet?
To remove and reset the device Once the controller is ready to remove your device, press and release the button on the smart outlet to remove it from the network. To return to factory defaults Press the button 3 times, then press and hold the button for at least 3 seconds. The LED will blink 5 times to confirm.
How do I reset my Jasco Z-wave light switch?
(Ask hub manufacture for more information on this.) For all our Z-wave plus in-wall switches you will click the upper switch 3 times rapidly, and the lower switch 3 times rapidly. On our paddle switches the blue LED will flash 5 times to confirm the reset (there is no LED on the toggle switches to confirm the reset).
How do I reset my Zigbee switch?
Devices with a reset button: Firstly, make sure the device is powered off for more than 10 seconds before powering on the device. Then long press the reset button on the device for about 5 seconds (for switch devices, the reset button is mostly the switch Button itself).
How do I reset my Z-wave SmartThings?
- Open SmartThings app.
- Tap Menu located at the top left corner of your screen.
- Tap Devices.
- Find your hub and select it.
- From the upper right 3 dot menu, tap Z-Wave Utilities.
- Tap Z-Wave Exclusion.
- Ensure that the LED on Smart Home Hub is blinking.
- Tap the button on the Z-Wave device that you want to factory reset.
How do I reset my Aeon Labs switch?
Wait for VENUS scan & detect this device and inform in app 2. Reset then re-add
- Press the button located between the LED. ( to reset)
- Press the button located between the LED. once more (to add)
How do I pair my Z-wave device?
Z-Wave / Zigbee Device Pairing Guide
- Click on add device
- Click on Other Devices. This will open the paring screen and the gateway will search for the new device.
- Follow the steps below to complete the pairing of the device with the gateway.
- Click on Add Device.
- Click on Other Devices.
- Power up the Z-Wave device.
How do I reset my GE outlet?
Factory Reset Indoor Smart Plugs
- While the Indoor Smart Plug is plugged into a wall outlet, hold the side on/off button, for at least 10 seconds.
- When LED indicator light turns red, let go of the button. The Indoor Smart Plug has been successfully reset.
How do I pair my GE smart outlet?
The LED light should blink blue indicating it is ready for setup.
- Launch the C by GE app on your phone or tablet.
- Tap Add in the top right corner.
- Then tap Add New Devices.
- Select Plugs.
- Select the Smart Plug from the list.
- Select your WiFi Network from the list and tap Continue.
How do I setup my GE smart switch?
- Launch the C by GE app on your phone or tablet.
- Tap Add in the top right corner.
- Then tap Add New Devices.
- Select C-Start Switches.
- Tap Get Started.
- Tap Continue when you see that light.
- Select the smart switch from the list. Select Continue to proceed.
- Select your WiFi network from the list and tap Continue.
How do I put my smart switch in pairing mode?
Turn off the switch. Press the top of the switch button 10 times. The indicator light at the bottom of the switch will blink blue three times. The smart switch will be paired with the hub when the indicator light stops blinking.
Reset Thermostat Schedule
Press and hold the ‘Up’ arrow and ‘Fan’ buttons. There will be a number on the left; change it to ’85’. There will be another number on the right; change it to ‘1’. The schedule of the thermostat is reset.
How do you manually reset a thermostat?
Here are the step-by-step reset instructions:
- Turn your thermostat off by switching it to the off position.
- Find the breaker that powers your HVAC system and turn it off.
- Wait 30 seconds and turn the breaker back on.
- Turn your thermostat back on.
What is Z-wave exclusion mode?
Remove Devices
Removing Devices is known as the Exclusion Process. It will not only remove a device from your Z-Wave hub but also factory reset the device. It doesn’t matter if the device has never been paired with your hub, exclusion mode will always give you a response no matter how many times you remove a device.