Complete the following steps to factory default your Kwikset Z-Wave Lock.
- Remove the cover. Take off the lock’s cover.
- Power down the lock. Remove the battery pack.
- Press and hold “Program”. Press and hold the “Program” button.
- Power on the lock.
- Wait for confirmation.
- Finish the reset.
How do you change the code on a Kwikset Z-Wave lock?
Press and HOLD Program button until keypad flashes green (about 5 seconds). Enter new mastercode. Press Lock button once. Re-enter mastercode.
How do I factory reset my Kwikset Smart Lock?
1 Factory Reset
- Open your door.
- Extend the latch bolt.
- Slide up the cover to open the back of your lock, exposing the buttons beneath.
- Push and hold the reset button for 10 seconds, until the lock beeps.
- The light ring will flash red, then spin amber.
- The lock has now been restored and is ready to be set up again.
How do you reprogram a smart lock?
Steps to re-keying Smart Key units (Note: You must have your Functioning Key and Learn Tool for this to work).
- Insert functioning key & turn 1/4 turn clockwise.
- Insert & remove the SmartKey learn tool. Remove functioning key.
- Insert new key & turn 1/2 turn counter-clockwise. Done. Your lock is now re-keyed! “”
How do I reset my smart code door lock?
Hold the button continuously for 30 seconds until you hear a beeping sound and see the status LED flashing red. Press the program button once again until you see the status LED flashing green and hear two beeping sounds. The Kwikset SmartCode deadbolt has now been reset and ready to be set up again.
How do you set a Z-Wave lock?
Complete the following steps to include your Yale Z-Wave Lock:
- Enter exclusion mode. You should put your alarm system into its Z-Wave exclusion mode for clearing devices.
- Clear the lock. Bring the Yale Lock into close proximity of the Z-Wave controller.
- Enter inclusion mode.
- Pair the lock.
How do you set up Z-wave Kwikset?
More videos on YouTube
- Enter exclusion mode. Put your system into its Z-Wave exclusion mode.
- Clear the lock. Bring the Kwikset Lock close to your panel or the Z-Wave controller.
- Enter inclusion mode. Now that the lock has been cleared, you can begin the pairing process.
- Pair the lock.
How do I reset my Kwikset lock code without the key?
A factory reset will delete all codes associated with the lock.
- Make sure the door is open and unlocked.
- Press and hold the program button for 30 seconds using the SmartKey tool or a paper clip. You will hear one long beep.
- Press and release the program button. You will hear one short beep.
How do I change the code on my electronic door lock?
First, open the door and lift off the lock’s interior cover. Press the Program button once and you should hear your unit beep five times and see its checkmark icon at the keypad’s bottom left flash five times. Press the checkmark once and then enter the master code.
How do I reset my Yale Z-Wave lock?
If you want to factory default your Yale Z-Wave Lock, complete the following steps:
- Prepare the lock. Remove the battery cover from the lock.
- Press the reset button. Press the reset button, and keep it held down.
- Reapply power. With the reset button held down, reinsert the battery to reapply power.
- Reassemble the lock.
How do I reset my Yale lock?
Remove the mounting plate to reveal the reset button, which is located on the left side of the cable connector. Hold down the reset button while you put in the batteries. Keep holding down on the reset button until the light turns red and the lock says Just a moment, erasing all settings. Release the reset button.
How do I pair my Z-wave device?
Z-Wave / Zigbee Device Pairing Guide
- Click on add device
- Click on Other Devices. This will open the paring screen and the gateway will search for the new device.
- Follow the steps below to complete the pairing of the device with the gateway.
- Click on Add Device.
- Click on Other Devices.
- Power up the Z-Wave device.
Why is my Kwikset lock not locking?
If there are no codes in the lock, the lock button will not lock the door.The battery is too low to lock the door. This is indicated by the keypad flashing red three times with three beeps. Remove the batteries and replace with a fresh set.
Is there an app to control Z-wave devices?
The system is managed via the tapHOME app, which is available free of charge, and tapHOME has also put together a special starter pack, with which residents can easily configure the basis for their home automation network.This allows any Z-Wave compatible device to be incorporated into the network as required.
For most Kwikset smart locks, the program button is on the inside of the interior assembly. You may need to remove the interior cover to access the program button.
Why is my Kwikset lock blinking red?
Amber flashes mean it is locked, while green flashes mean it is unlocked, and red means low battery.
Where is the Kwikset master code?
Make sure the lock is unlocked and the door is open. 2. Enter your Mastercode – for new install, default is 0-0-0-0.3. Press the lock button.
Why is my keypad door lock not working?
If the keypad buzzes twice after a code is entered and the door fails to unlock, this means the keypad is not communicating with the lock. A reset should fix this issue.To reboot the lock, remove one battery from the lock and replace it. Once you have rebooted the lock, try the entry code again.
Contents