How Do I Reset My Z-Wave Device?

1) Press and hold the Aeotec Z-Wave device for 20 seconds, then release to perform a Hard Reset.

How do I unpair a Z-wave device?

If the device is already paired with your Vera:

  1. Go to that device’s settings.
  2. Scroll down to the settings page and press delete device.
  3. Select unpair if your device is still connected to your network, and delete if the device is no longer connected.

How do I reset my Honeywell Z-wave switch?

Reset to factory default
Quickly press ON (Top) button three (3) times then immediatelypress the OFF (Bottom) button three (3) times. The LED will flashON/OFF 5 times when completed successfully.

How do I reset my Z-wave SmartThings?

  1. Open SmartThings app.
  2. Tap Menu located at the top left corner of your screen.
  3. Tap Devices.
  4. Find your hub and select it.
  5. From the upper right 3 dot menu, tap Z-Wave Utilities.
  6. Tap Z-Wave Exclusion.
  7. Ensure that the LED on Smart Home Hub is blinking.
  8. Tap the button on the Z-Wave device that you want to factory reset.

How do I delete a pairing device?

Delete Paired Bluetooth® Connection – Android™

  1. From a Home screen, do one of the following: Ensure Bluetooth is turned on. Navigate: Settings. Connected devices. Connection preferences. Bluetooth. . Navigate: Settings. Connected devices. .
  2. Tap the appropriate device name or the. Settings icon. (right).
  3. Tap ‘Forget’ or ‘Unpair’.

How do I reset my GE Z-Wave outlet?

To remove and reset the device Once the controller is ready to remove your device, press and release the button on the smart outlet to remove it from the network. To return to factory defaults Press the button 3 times, then press and hold the button for at least 3 seconds. The LED will blink 5 times to confirm.

See also  Is Eero Z-Wave Compatible?

How do I reset my Z-Wave garage door opener?

Reset the GD00Z-7 by pressing the LINK button 5 times. A quick beep followed by a longer beep will indicate the reset.

How do I reset my Z-Wave paddle switch?

For all our Z-wave plus in-wall switches you will click the upper switch 3 times rapidly, and the lower switch 3 times rapidly. On our paddle switches the blue LED will flash 5 times to confirm the reset (there is no LED on the toggle switches to confirm the reset).

How do you reset a Z-Wave deadbolt?

Complete the following steps to factory default your Kwikset Z-Wave Lock.

  1. Remove the cover. Take off the lock’s cover.
  2. Power down the lock. Remove the battery pack.
  3. Press and hold “Program”. Press and hold the “Program” button.
  4. Power on the lock.
  5. Wait for confirmation.
  6. Finish the reset.

How do you delete find my devices?

How to disable Find My Device on your phone

  1. Open Settings from the home screen.
  2. Navigate to Security & lock screen.
  3. Select Find My Device.
  4. Toggle Find My Device to Off.

How do I undo forget this device?

Once you forget a device, the phone will not show it in the list of devices on Bluetooth. To Unforget the device, you need to reset the network settings. To do that, open your phone’s Settings and then scroll down to “System.” From the System tab, you will see “Reset Options” from where you should reset the phone.

How do you reset a Z-Wave light bulb?

Just screw the bulb into a standard E27 light bulb socket. Device Reset For device reset the device must be turned on and off 4 times in a row within 4 seconds. On factory default the device does not belong to any Z-Wave network.

See also  How Do You Fly With A Lithium Battery?

How do you fix a receptacle that won’t reset?

GFCI Outlet Won’t Reset: Troubleshooting GFCI and Other Dead Outlets

  1. Check if the other outlets are dead.
  2. Check for the tripped circuit or a blown fuse.
  3. Check the GFCIs.
  4. Look for loose or bad connections.
  5. Reinstall the connector.

How do I reset my GE oven control panel?

Reset the electronic control. Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.

How do I reset my garage door opener signal?

The basic process goes something like this: First, you’ll want to open the access panel on the backside of your garage door opener. Look for a button that says “Learn” and hold that down until the light starts blinking. Now you’ve reset your door codes and your remotes should not work.

How do I reset my keyless garage door entry?

Program Garage Door Keypad PIN Using Your Garage Door Opener
Press and release the LEARN button. Once the LED is lit, you will have 30 seconds to complete the next step. Enter a 4-digit PIN of your choice, then press and hold the ENTER button until the garage door opener light blinks. The PIN programming is complete.

How do I reset my device switch?

Here’s how.

  1. On the Nintendo Switch home screen, select Settings.
  2. Scroll down and select System on the left menu.
  3. Scroll to the bottom of the screen and select Formatting Options.
  4. Choose Initialize Console, and then select OK.
  5. Wait for the console to finish erasing your data.
See also  Can Siri Turn On Tv?

How do I reset my Swi?

How to reset a Nintendo Switch

  1. Press the small circular power button on top of the Switch console, and hold it down until the system powers off.
  2. Wait a few seconds, then press the power button again.
  3. The Switch should display the Nintendo logo, and then turn on again within a few moments.

How do I reset my FS switch?

Step 4: Enter the username and password. The default username is admin. The default password is admin. You are now ready to configure the switch.

Contents

This entry was posted in Smart Lock by Silvia Barton. Bookmark the permalink.
Avatar photo

About Silvia Barton

Silvia Barton is someone who really enjoys smart devices. She thinks they make life a lot easier and more fun. Silvia loves to try out new gadgets and she's always on the lookout for the latest and greatest thing in the world of technology.