9400 – HD PVR Receiver
- If you can’t see any picture on your TV, reset your receiver by pressing and holding the POWER button for 5 seconds.
- On your Satellite TV remote, press MENU.
- Scroll to and select System Setup.
- Scroll to and select Factory Defaults.
- Read the warning and select Yes.
https://www.youtube.com/watch?v=i-71kB_ihlc
How do I reset my Bell Fibe PVR?
How to reset my Fibe TV receiver
- Unplug the power cable on the back of the Fibe TV receiver.
- Wait 10 seconds.
- Reinsert the cable.
- Wait approximately five minutes for the Fibe TV receiver to restart.
Why is my Bell Fibe PVR not working?
Try switching the receiver to standby mode by pressing the POWER button. Turn off any other receivers that may be active but not in use. Reboot the receiver by pressing and holding the POWER button for 5 seconds (until the red, green and blue lights in the centre go on and off).
How do I reset my Shaw PVR box?
How to reset your digital box
- Locate and unplug the power cable on your Digital Box.
- Wait 30 seconds.
- Plug the power back into the Digital Box.
- Wait approximately 1-2 minutes for the Interactive Guide functions to be fully restored.
Why is my Shaw PVR not working?
Troubleshoot your unresponsive digital box by locating and unplugging the power cable. Wait 30 seconds and reconnect the power cable to the digital box. Wait approximately 1-2 minutes for the digital box to reboot. Power the digital box on and test if it is now responsive.
How do I reset my Bell Fibe modem?
How to reboot the modem
- On your modem, locate the power cable.
- Remove the cable. Wait 10 seconds and reinsert the cable.
- The lights on the front of your modem (except for the power LED) will blink as the modem goes through its start-up routine.
- Wait until the WAN and INTERNET lights turn blue.
How do I reset my Bell Satellite Receiver?
How to reset your Bell Satellite TV receiver to the factory…
- Press MENU on your remote control.
- Select System Setup.
- Select Factory Defaults.
- A pop-up message will appear to confirm that you want to reset your receiver to the factory default settings.
- Select Yes.
How do I fix my bell PVR?
9400 – HD PVR Receiver
- If you can’t see any picture on your TV, reset your receiver by pressing and holding the POWER button for 5 seconds.
- On your Satellite TV remote, press MENU.
- Scroll to and select System Setup.
- Scroll to and select Factory Defaults.
- Read the warning and select Yes.
How do I turn on PVR on Bell Fibe?
How to activate your wired HD receiver or PVR
- Once you see the Fibe TV activation screen, press SELECT to begin the activation.
- Select the desired language.
- Select Activate.
- If you?re repairing a PVR, press SELECT to restart your HD PVR.
- If you have an HD PVR, it?s now restarting.
How do I set my bell PVR?
How to record shows on my Bell Satellite TV (6400 HD receiver) PVR using the show’s name or a keyword (name based recording)
- Press the PVR button twice.
- Select Vu Pass.
- Select Title to search for programs by title.
- Select Info to search for programs whose descriptions and titles contain keywords.
How do I reboot my Shaw box?
How to reboot using the Power button
- Ensure your cables are tightly secured.
- Press and hold the Power button located on the front of the TV box for 10 seconds.
- The TV box should automatically reboot.
How do I reset my Shaw receiver?
To reset your receiver:
- Unplug the receiver’s power cord from the back of the receiver or from the wall outlet.
- Leave unplugged for 30 seconds and plug back in.
- The receiver should boot up properly in less than 90 seconds.
How do I reset my Shaw modem?
Locate the small pin-hole reset button located on the back of the Shaw WiFi Modem. Push and hold this button down for 15 seconds with a paper clip or pen. This will cause the modem lights to begin to flash and after a few moments, the modem will come back online.
How do I get my cable box to work again?
Reboot the cable box by unplugging it from the wall outlet. Wait about 20 seconds, then plug it back in. This should cause an automatic reboot which will usually fix most problems, including a frozen picture and features which no longer work. If a reboot doesn’t do the trick, phone your cable company.
Why won’t my Shaw box turn on?
Restart your TV box
Remove the power cable from the back of the unit. Unplug the power cable from the wall outlet or power bar. Wait 30 seconds, then reconnect the power cable. Power on your TV box to see if it works.
How do I reset my Bell Fibe 3000 modem?
To reset your Home Hub 3000:
- Press and hold the Reset button on the side of the modem for at least 30 seconds.
- The Power light will flash red 5 times to indicate the process has started.
- Open a web browser and follow the online instructions.
How do I reset my Bell 3000 modem?
To restart your Home Hub 3000 modem
- Press and hold the Reset button on the side of the modem for 5 seconds.
- Wait until all 3 LED lights are white and Fibe Internet: Connected is displayed.
How do I reset my modem and router?
Step 1: Unplug the modem and router from the power outlet. Step 2: Wait at least 15 seconds. Step 3: Plug the modem back into the power outlet first, wait 1-2 minutes, then it’s time to power on the router. Step 4: Wait for all panel lights on your cable modem to become green on before testing your internet connection.
How do I reset my Bell PVR 9241?
9241 – HD PVR Plus Receiver
- If you can’t see any picture on your TV, reset your receiver by pressing and holding the POWER button for 5 seconds.
- On your Satellite TV remote, press MENU.
- Scroll to and select System Setup.
- Scroll to and select Factory Defaults.
- Read the warning and select Yes.
How do you reset a bell receiver?
Reboot your receiver
- Press and hold-down the green POWER button on the front of your TV receiver for 5 seconds (until the red, green, and blue lights come on).
- Wait a few minutes for the reboot to take place.
- Once the reboot completes, content from the channel that you last viewed appears.
How do I refresh my satellite receiver?
How to reset your receiver
- Unplug the power cord from the back of the receiver.
- Leave it unplugged for 30 seconds, then plug it back in.
- The receiver should boot up properly in less than 90 seconds, with lights flashing in front.
Contents