How do I reset my irrigation system?
How to Reset a Sprinkler System
- Turn the control dial to the “off” position.
- Press the “next” button to access the clear-memory feature.
- Press and hold the “off” button until the display stops blinking.
- Turn the control dial to the “run” position.
- Press and hold down the “minus” arrow and “prog” buttons simultaneously.
How do I start Hunter Pro C?
Hunter controllers allow you to start a station or an entire program manually. To do so, turn the dial to Manual Single Station or Manual All Stations, verify that the stations that you want to activate have run time, and turn the dial back to the Run position.
Press and release the RESET button on the back of the front panel.
How do I reset my hunter X2 sprinkler?
X2 – Total Reset
- Turn the dial to the RUN position.
- Press and hold the program button.
- Press and release the RESET button located inside the lower wiring compartment.
- When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.
Is there an app for Hunter sprinkler system?
Hunter Hydrawise
Remote access is possible through either the Hydrawise app (iOS or Android compatible devices) or online through their cloud software. Key product features include: Predictive Watering Adjustments based on web-based weather data brings up to 50 percent in water savings.
What does P err mean on a Hunter Pro C?
CAUSE – The P ERR message is displayed when the P/MV circuit is drawing too much current. Common causes include; a defective solenoid on the master valve, incompatible or defective pump relay, or wire run too long between the relay and controller.
What does err mean on sprinkler system?
Err indicates that a station has faulted due to a short on that output. Common reasons for this station fault include: 1) a defective solenoid, 2) defective field wiring, or 3) poor wire connections. STEP 1: Verify Station Fault. Remove the field wire for the faulted station.
Why does my sprinkler system say no AC?
The “No AC” means the battery is powering the unit but won’t power the sprinkler controls. It’s either the prime power source or the unit.
Why is my irrigation system not working?
If your sprinkler system is not getting water, a number of things could be the culprit: The backflow may be off. If the handle on your backflow valve gets inadvertently shut off, it restricts any water from flowing past the backflow and to the sprinkler system valves. Your rain sensor might be faulty.
Why is my controller not starting the watering cycle?
Check for Rain Sensor operation
Look at the Sensor terminals on the controller.By sliding the Rain Sensor switch to the Bypass position you can over-ride the active sensor. Look at the controller display, if the Sensor OFF message is displayed, the sensor is activated and inhibiting the watering cycles.
Why does my irrigation system finish watering and then start again?
A common reason why a program is repeating is that you have a second start time set. The start times control the exact time your ESP-Me timer will begin to water and they also control how many times a day your timer will water. The ESP-Me allows you to set up to 6 start times per program.
How do I clear my hunter thermostat?
You can reset them all at the same time using the reset button.
- Open the faceplate on the Hunter thermostat.
- Twist a paper clip so one of the ends is sticking out.
- Press the end of the paper clip into the “Reset” pinhole and hold it for two seconds to clear the programming.
What does a flashing 3 mean on a Hunter thermostat?
A flashing 3 means the third setting is currently operating the heater or AC.
How do I reset my Hunter SRC Plus sprinkler?
SRC Plus Reset
- Press and hold down the , and buttons.
- Press and release the RESET button in the lower wiring compartment.
- Release the , and buttons. The display should now show 12:00a. m.
- All the memory has been cleared and the controller may now be reprogrammed.
How do you bypass a hunter rain sensor?
Simply turn the dial to RUN (BYPASS SENSOR) and the weather sensor will be overridden. The wireless rain sensor may be bypassed by using the built-in bypass feature on the receiver. To bypass the sensor, press the SENSOR BYPASS button on the receiver. The bypass status light will turn red when the sensor is bypassed.
Is Hunter Hydrawise free?
Hydrawise Plans and Pricing
The Hydrawise system is free for most users worldwide. The Weather Underground award-winning forecasting and airport weather stations meet the needs of the typical user.
What is Hydrawise app?
Hydrawise automatically adjusts watering based on highly accurate, internet-sourced local weather data. The system looks at the forecast and past history to ensure that just the right amount of irrigation is applied.This leads to significant water savings from your sprinkler system, saving you both time and money.
How long does a hunter sprinkler controller last?
One of the components that you may need to replace regularly are the wires, often due to improper installation and corrosion. Valves will give you 10 to 15 years of service, while controllers 5 to 10 years.
How do I know if my sprinkler controller is bad?
Sprinkler System Troubleshooting 5 Signs Of A Faulty System
- Controller Isn’t Working Properly.
- Low or High Water Pressure.
- Sprinkler is Stuck or Won’t Come Up.
- Puddles on Lawn or Around Sprinkler.
- Uneven Spray Patterns.
- When to Call a Professional.
What is a pump start relay?
A pump start relay is a relay box that activates a pump every time a zone is activated from the controller.Whenever one of the irrigation zone valves is told to open by the controller, the controller also signals the pump start relay to turn the pump on.
Contents