How Do I Reprogram My Somfy Keygo Remote?

Receiver type 1:

  1. Open the cover of the receiver, located next to your motor.
  2. Press the programming button “Prog 1” on the receiver circuit board. The LED L1 lights up.
  3. Press any button on your new transmitter.
  4. Wait 10 seconds.
  5. Your new remote control is successfully programmed.

What is the My button on Somfy remote?

What is the “My Button”? The “My Button” on Somfy remote controls has two purposes. It is a stop button when the shades are in motion. But for programming purposes, it is what I call a favorite position button.

How do I reset my Somfy remote awning?

Press and hold the “Programming” button on the back of the remote a second time until the awning moves back and forth in short movements. The remote control is now reset and ready for normal use.

Why is my Somfy remote blinking red?

Once you plug-in the device and switch it on the myLink will blink red. Open the myLink app and press Start New System. Follow the prompts for setup as they appear on screen. The solid red LED light is an indicator that the myLink is in setup mode.

How do I pair my Somfy remote to my blinds?

Press and hold the motor head button until the blinds briefly moves Up and Down. Release the button once complete. Briefly press the motor head button, the blind will briefly move Up and Down twice.

How do I reset my somfy battery motor?

To reset the motor, press and hold the motor head programming button until the driven product briefly moves Up and Down 3 times. All the settings are erased. The driven product must be programmed.

See also  What Are The Disadvantages Of Health Monitoring?

How do you program a somfy awning motor?

Press & hold both the MY/ STOP and DOWN buttons until the awning begins to extend, then release. Stop at the desired lower limit, adjust by pressing the UP or DOWN buttons. PROGRAMMING BUTTON on the back of the transmitter. The motor will jog confirming limit settings and is now in User Mode.

How do you troubleshoot Somfy?

More videos on YouTube

  1. Step 1: Press and hold “my” for 8 seconds, the light should blink the entire time.
  2. Step 2: Unplug the motor and plug it back in.
  3. Step 3: Check power at the quick connect outlet or power source.
  4. Step 4: Plug the motor into a different outlet.

What is rolling code programming?

Rolling code protects against intruders by generating a new security code every time the remote control is used on your garage door opener.The previously used code will be discarded, and the opener will only to respond to the new code the next time the remote control is used.

What is a rolling code system?

A rolling code (or sometimes called a hopping code) is used in keyless entry systems to prevent replay attacks, where an eavesdropper records the transmission and replays it at a later time to cause the receiver to ‘unlock’. Such systems are typical in garage door openers and keyless car entry systems.

How do I know if I have a rolling code garage door?

You can also look on your remote transmitter to see if the words SECURITY+ or Rolling Code can be found. If this is the case, know that your door opener has the built in rolling code technology. This means that after every single use of your garage door, the code on your transmitter changes.

See also  Can You Use Philips Hue With A Normal Light Switch?

How do I reset my remote control?

Solution 5: Resetting Spectrum Remote to Factory Defaults

  1. Press and hold the TV button.
  2. While you are still holding it, press the OK button for 1 second and then release both buttons at the same time.
  3. Now you have to press and hold the Delete button for 3 seconds.
  4. Now your TV remote will be reset to factory settings.

How do I fix an unresponsive remote?

Clean the remote control terminals. The remote control battery terminals may be dirty. Remove the batteries and clean the remote control terminals with a small solution of alcohol, using a cotton bud or soft cloth, then place the batteries back into the remote control. Replace with fresh batteries.

What to do when remote is not working?

Section B: Checking items of the remote control (common)

  1. Make sure none of the remote buttons are jammed.
  2. Reset the remote.
  3. Clean the remote control terminals.
  4. Replace with fresh batteries.
  5. Perform a power reset on the TV.
  6. For Android TV/Google TV: symptoms may improve by updating the software of the remote control.

Contents

This entry was posted in Smart Home by Alyssa Stevenson. Bookmark the permalink.
Avatar photo

About Alyssa Stevenson

Alyssa Stevenson loves smart devices. She is an expert in the field and has spent years researching and developing new ways to make our lives easier. Alyssa has also been a vocal advocate for the responsible use of technology, working to ensure that our devices don't overtake our lives.